MVME162P-344SE工控备件机器人模块
烧伤危险：标签可能位于设备上或内部，例如驱动器或电机，以提醒人们表面可能达到危险温度。致动距离：响应距离：最大速度：控制单元通电后，还必须按下该按钮。与控制单元的外形连接这些端子用于将外形连接到：=棕色内部导体。=白色外部连接器。参见应用。注：配置文件必须以结尾Ω串联电阻黄色。当两个外形直接连接到和并联时，每个外形应使用电阻器蓝色终止。并联和串联连接可选连接方法并联连接最多可以并联两个型材，以帮助在某些应用中轻松布线。使用电阻器蓝色串联连接如果要使用多个配置文件，它们通常如图所示串联连接。使用电阻器黄色电气连接安全控制单元表面安装导轨安装+电源保险丝停止红色打开黄色运行绿色电源保险丝安全保险丝+停止红色打开黄色指示灯运行绿色控制单元安装和布线按照步骤至正确安装重要事项：布线必须符合国家电气规范和适用的地方法规和条例电源选择开关如果使用或电源，则应在打开电源前适当设置电压选择开关。该装置在制造时设置为。电源输入端子如果使用或电源，则应将其与保护接地接地一起连接至所示端子。
保护接地线的尺寸应至少等于电源线的尺寸。同时检查如果使用这些端子，则忽略输入端子+和如果使用电源，则应将电源连接到这些端子，以确保观察到正确的极性。不要与的端子进行任何连接。如果使用或电源，则必须根据国际电气安全规程将其与主电源隔离。一个极应接地。对于，负极应接地接地。对于，电源的接地接地极应连接到端子。辅助输出端子和该端子提供了一个辅助常闭触点即，当绿色“运行”灯熄灭时闭合，适用于指示或报警装置。由于这是一个辅助设备，因此不得将其连接到安全电路。安全输出端子和这些是用于连接到机器安全电路的无电压触点，即它们与机器接触器控制电路串联连接。时的最大额定值。这两个安全电路都有内部保险丝，但也必须使用快速熔断器进行外部保护。如果使用一个接触器，则需要端子和，端子和应跨接在一起。对于具有个独立控制电路即双通道系统的个接触器，一个接触器使用，另一个接触器采用。
Burn hazard: Labels may be located on or inside equipment, such as drives or motors, to warn people that the surface may reach dangerous temperatures. Actuation distance: response distance: maximum speed: the button must be pressed after the control unit is powered on. Connection to the profile of the control unit These terminals are used to connect the profile to the:=brown internal conductor= White external connector. See Application. Note: The configuration file must end in Ω series resistance yellow. When two profiles are connected directly to and in parallel, each profile shall be terminated in blue with a resistor. Parallel connection and series connection Optional connection methods Parallel connection can be used to connect up to two profiles in parallel to facilitate easy wiring in some applications. Use resistor blue series connection If you want to use multiple configuration files, they are usually connected in series as shown in the figure. Use resistor yellow for electrical connection Safety control unit Surface mounting rail installation+power fuse stop red for operation Green power fuse safety fuse+stop red for operation Yellow indicator light for operation Green control unit installation and wiring Follow steps to correct installation Important: Wiring must comply with national electrical specifications and applicable local regulations and rules Power selection switch if used or power supply, The voltage selector switch shall be set properly before turning on the power supply. The device is set to at the time of manufacture. If the or power supply is used, the power input terminal shall be connected to the terminal shown together with the protective grounding.
The size of the protective earth wire shall be at least equal to the size of the power line. Also check that if these terminals are used, the input terminals+are ignored and if a power supply is used, the power supply should be connected to these terminals to ensure that the correct polarity is observed. Do not make any connections to the terminals of. If the or power supply is used, it must be isolated from the main power supply according to the international electrical safety regulations. One pole should be grounded. For, the negative pole should be grounded. For, the grounding electrode of the power supply shall be connected to the terminal. The auxiliary output terminal and the terminal provide an auxiliary normally closed contact, that is, it is closed when the green "running" light is off, and it is applicable to the indication or alarm device. Since this is an auxiliary device, it must not be connected to a safety circuit. The safety output terminals and these are voltage free contacts used to connect to the machine safety circuit, that is, they are connected in series with the machine contactor control circuit. Maximum rating at. Both safety circuits have internal fuses, but they must also be externally protected with quick fuses. If a contactor is used, terminals and shall be connected together. For each contactor with independent control circuit, i.e. dual channel system, one contactor is used and the other contactor is used.
