MVME162PA-242LE模拟量输入模块
端子是安全的。照明。链接到位或重置按钮功能正常。装置似乎工作保险丝熔断。输出保险丝。正确，但没有损坏或不正确的接线。所有接线是否损坏。输出上的故障导致任何内部继电器移动。故障安全输出 。如果外部连接不正确，机器不会停止所有到接触器的接线都有错误。轮廓已按下。运行“绿色”熄灭。如果按下“不允许使用机器配置文件”，机器不会停止。更换控制器。运行“绿色”保持亮起。维护在尝试任何维护工作之前，应完整阅读本节内容。请注意欧盟指令作为年工作设备的提供和使用条例在英国实施下的计划预防性维护条例。在维护操作期间，在使用系统之前，断开机器的原动机。遵守电气安全预防措施。 当使用带密封的封闭盖时，必须将型材底部切回的长度。必须小心切割，以确保型材底部完全修剪，不会留下齐平表面。阴影区域必须用砂纸打磨粗糙封口盖用个密封圈模制，每个密封圈带有一个橡胶塞。安装电阻器时，保持插头完好无损。在进行电缆连接时，选择所需的电缆出口，并用打孔器从索环上取下插头。将连接电缆穿过孔。 用其中一根针刺破每根铜线。按所示方向向外楔入将接头的针触点直接压入铜线。小心连接器的窄侧楔形必须向外突出。折回盖的密封唇 如图所示，在封口盖的阴影区域涂上粘合剂，然后粘贴到型材边缘，加压秒以确保粘合。 在阴影区域的其余部分涂上粘合剂，使密封唇与型材接触。重要事项：将粘合剂均匀涂抹在阴影区域！不要让粘合剂进入型材内部。应用 +棕白色
The terminal is safe. Lighting. Link in place or reset button functions normally. The unit appears to be working with a blown fuse. Output fuse. Correct, but no damaged or incorrect wiring. Whether all wiring is damaged. A fault on the output causes any internal relays to move. Fail safe output. If the external connection is incorrect, the machine will not stop all the wiring to the contactor has errors. Contour pressed. Running "green" turns off. If you press "Do not allow to use machine configuration file", the machine will not stop. Replace the controller. Running "green" remains lit. Maintenance Read this section completely before attempting any maintenance work. Please note the planned preventive maintenance regulations under the EU Directive as an annual provision and use of working equipment in the UK. During maintenance operations, disconnect the prime mover of the machine before using the system. Observe electrical safety precautions. When using a closed cover with a seal, the bottom of the profile must be cut back to the length. Care must be taken in cutting to ensure that the bottom of the profile is completely trimmed without leaving a flush surface. The shadowed area must be sanded rough. The closure cap is molded with sealing rings, each with a rubber plug. Keep the plug intact when installing the resistor. When connecting cables, select the required cable outlet and use a hole punch to remove the plug from the grommet. Pass the connecting cable through the hole. Pierce each copper wire with one of the needles. Press the pin contact of the connector directly into the copper wire by wedging outward in the direction shown. Be careful that the narrow side wedge of the connector must protrude outward. The sealing lip of the fold back cover is as shown in the figure. Apply adhesive to the shaded area of the cover, and then stick it to the edge of the profile. Press for seconds to ensure adhesion. Apply adhesive to the rest of the shaded area so that the sealing lip contacts the profile. IMPORTANT: Apply the adhesive evenly to the shaded area! Do not allow the adhesive to enter the inside of the profile. Application+brown white
