MVME162PA-242LNS自动化卡件
日常维护检查和测试建议每周或维修后停止机器，清洁型材并干燥。检查型材表面是否损坏。任何刺穿型材的损坏都可能让材料或液体进入。必须立即处理。检查所有端盖角和接头是否牢固且无损坏。必须立即更换损坏的零件。测试配置文件操作。两个人可能需要一个人按下配置文件，一个人观察控制单元的操作。在使用手动复位模式的系统上，必须连续按下复位按钮。检查配置文件未按下时“绿色”是否亮起，“红色”是否点亮。启动机器，按下配置文件并检查机器是否立即停止。如果这些检查发现任何问题，则在纠正之前不得使用机器。将所有检查和测试记录在书面日志中。彻底检查和测试每年两次或维修后由电气和机械工程方面的合格人员进行。 执行 中的测试，隔离机器和系统的电源。遵守电气安全预防措施。 彻底检查型材和部件有无机械损坏。 断开端子处的轮廓线。将轮廓线的导线连接到欧姆表的输入端。现在，一个人应该用一只手按压条带上的每个点。电阻测量值应为 + 未按下型材时为，按下型材时不超过。如果检查发现任何问题，则在纠正之前不得使用机器。将检查和测试记录在书面日志中。 维护和服务故障查找指南症状可能原因检查剖面中的“黄色”开路或端子是否牢固。照明。连接接线。电缆断裂剖面图损坏。即使电源故障，也不会点亮。电压选择开关设置正确。轮廓被按下。电源保险丝。存在电源电压。除非复位失败，否则不会点亮。如果使用接触器监视器，请检查是否按下配置文件，然后每个接触器是否正常工作
Daily maintenance, inspection and testing suggest stopping the machine every week or after maintenance, cleaning and drying the profiles. Check whether the profile surface is damaged. Any damage that pierces the profile may allow material or liquid to enter. It must be handled immediately. Check that all end cap corners and connections are secure and undamaged. Damaged parts must be replaced immediately. Test configuration file operation. Two people may need one to press the configuration file and the other to observe the operation of the control unit. On systems using manual reset mode, the reset button must be pressed continuously. Check whether "green" lights up and "red" lights up when the configuration file is not pressed. Start the machine, press the configuration file and check if the machine stops immediately. If these checks reveal any problems, do not use the machine until it is corrected. Record all inspections and tests in a written log. Thorough inspection and testing shall be conducted twice a year or by qualified personnel in electrical and mechanical engineering after maintenance. Perform the test in to isolate the power supply of the machine and system. Observe electrical safety precautions. Thoroughly inspect the profiles and components for mechanical damage. Disconnect the contour line at the terminal. Connect the lead of the contour line to the input of the ohmmeter. Now, one should press each point on the strip with one hand. The measured resistance value shall be +when the profile is not pressed, it shall not exceed. If any problems are found during the inspection, the machine must not be used until it is corrected. Record inspections and tests in a written log. Maintenance and Service Fault Finding Guide Possible Causes of Symptoms Check the "yellow" open circuit in the section or whether the terminal is secure. Lighting. Connect the wiring. The cable fracture profile is damaged. It will not light up even if the power supply fails. The voltage selector switch is set correctly. The contour is pressed. Power fuse. Supply voltage is present. It will not light up unless reset fails. If a contactor monitor is used, check whether the configuration file is pressed, and then whether each contactor works normally
