MVME167-003B工业备件
这将允许SOE模块以UTC时间标记事件。因此，用户需要在1756HP-TIME模块上启用CST主控，并将UTC和CST对复制到每个SOE模块输出组件。CST主控权可以通过配置映像UDT或AOP:Hidrom 8 TE启用：如果用户使用1756HP-TIME模块的主要固件版本2，则可以通过附加配置文件（AOP）完成所有设置，并且图像结构化时需要UDT。用户可以复制CST和UTC对，如下所示：完成后，SOE模块将指示它正在报告UTC时间戳：当SOE模块上发生事件时，将为UTC值加上时间戳。Hidrom 9这可以复制到LINT类型的变量中，并以DateTime格式查看，以查看公历日期。RSLogix v19如果用户未使用CIPSync（精确时间协议–PTP），则RSLogix v16方法也适用于RSLogix V10。精确时间协议（PTP）将使用以下冗余PLC架构作为示例：Hidrom 10 RSLogix v9使用CIPSync时，用户必须启用3个选项。这将允许1756HP-TIME模块在不需要任何阶梯的情况下同步SOE模块：TE：只有1756-IB16ISOE模块的主要版本2支持CIPSync（PTP）。1.将1756HP-TIME模块设置为在配置图像UDT或AOP:TE中输出PTP：如果用户正在使用1756HP_TIME模块的主要固件版本2，则所有设置都可以从附加配置文件（AOP）中完成，并且图像结构化时需要UDT。2.设置以太网网桥模块（EN2 EN2TR等）以支持CIPSync:Hidrom 11 3.使用CIPSync（PTP）将SOE模块设置为时间戳：Hidrom 12以太网网桥将用作每个机架的边界时钟（以太网上的PTP从设备和控制总线上的PTP-主设备）。因此，SOE模块将与以太网桥同步，而以太网桥又将与1756HP-TIME模块同步。一旦SOE模块与TIME模块同步，它将指示时间戳将通过CIPSync从TIME模块提供UTC：当事件发生时，SOE模块将对UTC值进行时间戳。Hidrom 13这可以复制到LINT类型的变量中，并以DateTime格式查看，以查看公历日期。Hidrom Hiprom电话：+27 11 787 4458传真：+27 1 787 7937邮政信箱732 Pinegowrie南非2123物理369比勒陀利亚大道芬代尔，Randburg South Africa 14技术数据旋转式断开开关规格公告编号194R附加资源这些文档包含有关相关产品的附加信息。您可以查看或下载出版物，网址为http：文献。要订购技术文件的纸质副本，请联系当地经销商或销售代表。主题页产品线概述2一般规格3保险丝说明12近似尺寸14资源描述工业自动化布线和接地指南出版物1770-4.1提供了安装工业系统的一般指南。产品认证网站，提供符合性声明、证书和其他认证详细信息。
This will allow the SOE module to timestamp events in UTC time. Thus the user will need to enable the CST Mastership on the 1756HP-TIME module and copy the UTC and CST pairs to each SOE module output assembly. The CST Mastership can be enabled either via the Config image UDT or AOP: Hiprom 8 TE: If the user is using major firmware revision 2 of the 1756HP-TIME module all setting can be done from the Add-on Profile (AOP) and UDTs are required as the images are structured. The user can copy the CST and UTC pairs as shown below: Once this is done the SOE module will indicate that it is reporting back UTC timestamps: When an event occurs on the SOE module will timestamp the UTC value. Hiprom 9 This can be copied into a variable of type LINT and viewed in DateTime format to see the Gregorian Date. RSLogix v19 If the user is t using CIPSync (Precision Time Protocol – PTP) then the RSLogix v16 method will also apply to RSLogix v19. Precision Time Protocol (PTP) The following redundant PLC architecture will be used as an example: Hiprom 10 RSLogix v19 When using CIPSync (PTP) the user must enable 3 options. This will allow the 1756HP-TIME module to synchronize the SOE modules without any ladder needed: TE: Only major revision 2 of the 1756-IB16ISOE module will support CIPSync (PTP). 1. Set the 1756HP-TIME module to output PTP in either the config image UDT or AOP: TE: If the user is using major firmware revision 2 of the 1756HP-TIME module all setting can be done from the Add-on Profile (AOP) and UDTs are required as the images are structured. 2. Set the Ethernet bridge module (EN2 EN2TR etc.) to support CIPSync: Hiprom 11 3. Set the SOE module to timestamp using CIPSync (PTP): Hiprom 12 The Ethernet Bridge will serve as a boundary clock (PTP slave on Ethernet and PTP master on ControlBus) for each rack. Thus the SOE module will synchronize to the Ethernet Bridge which in turn will synchronize to the 1756HP-TIME module. Once the SOE module has synchronized to the TIME module it will indicate that the timestamps will provide the UTC from the TIME module via CIPSync: When an event occurs the SOE module will timestamp the UTC value. Hiprom 13 This can be copied into a variable of type LINT and view in DateTime format to see the Gregorian Date. Hiprom HIPROM TEL: +27 11 787 4458 FAX: +27 11 787 7937 POSTAL P.O. Box 732 Pinegowrie South Africa 2123 PHYSICAL 369 Pretoria ave Ferndale, Randburg South Africa 14Technical Data Rotary Disconnect Switch Specifications Bulletin Number 194R Additional Resources These documents contain additional information concerning related products from . You can view or download publications at http:literature. To order paper copies of technical documentatio contact your local distributor or sales representative. Topic Page Product Line Overview 2 General Specifications 3 Fuse Description 12 Approximate Dimensions 14 Resource Description Industrial Automation Wiring and Grounding Guideline publication 1770-4.1 Provides general guidelines for installing a industrial system. Product Certifications website, Provides declarations of conformity, certificate and other certification details.
