MVME167P-35SE自动化模块备件
将电缆插头与电机接头配合时，不要用力过猛。如果插头和连接器不能用轻微的手用力连接在一起，请重新对齐平面并重试。重要事项所示电机方向用于清楚显示每个电缆插座上的对准标记。安装时建议的电机方向将接头定位在电机底部。提示：完全固定的螺纹插头在接头和插头之间留下一个小开口，大约为1…4 mm（0.04…0.16 in.）。注意：对齐键控连接器并手动拧紧建议的圈数。如果无法用手拧紧接头，请检查键控接头是否正确对齐。不要使用工具（例如钳子和虎钳）拧紧接头。制动器和电源连接器反馈连接器对齐平面对齐平面MP系列75 mm或更小框架尺寸的低惯量无刷伺服电机13罗克韦尔自动化出版物MP-IN006D-EN-P-2015年1月产品尺寸本节提供了电机的尺寸。LB T L-LB D L LE F G N P LA HD AD 53.9（2.12）LD见详图A 2.8±0.30（0.110±0.012）轴直径公差MPL-A/B1510、-A/B1520、-A/B1530电机：▸8.998…9.007（0.3543…0.3546）MPL-A/B210、-A/B220，-A/B230电机：Ö10997…11.008（0.4330…0.4334）详图A轴直径MPL-A/B 1xxx和MPL-AB2xx电机：▸11.89…11.95（0.468…0.470）动力/制动连接器反馈连接器M直径螺栓圆上的S直径孔尺寸单位为mm（in.）轴端螺纹孔MPL-A/B1510、-A/B1520、-A/B1530电机：螺纹-M3 x 0.5-6H螺纹深度-9.0（0.35）MPL-A/B210、-A/B220、
-A/B230电机：螺纹-M4 x 0.7-6H螺纹深度-10.0（0.39）连接器外壳可在180°导向直径公差范围内旋转MPL-A/B1510、-A/B1520、-A/B1530电机：Ö39.995…40.011（1.5746…1.5752）MPL-A/B210、-A/B220、-A/B230电机：▸59.993…60.012（2.3619…2.3627，-A/B230=4 x 4 x 16键14 MP系列低惯量无刷伺服电机，框架尺寸为75 mm或更小罗克韦尔自动化出版物MP-IN006D-EN-P-2015年1月MPL-A/B15xx和MPL-A/B2xx电机尺寸电机设计为公制尺寸。英寸尺寸是毫米的近似换算。无公差的尺寸仅供参考。电机类别。编号ADmm（in.）HDmm（in.）T mm（in..）LA mm（in.。）LD（1）mm（in，并增加了更小的框架尺寸15罗克韦尔自动化出版物MP-IN006D-EN-P-2015年1月公差和补充尺寸电机负载力额定值电机能够在持续的轴负载下运行。图中显示了径向和轴向负载力的位置，并列出了最大值。载荷以磅为单位，千克为数学换算。轴上的负载力下表表示了各种负载和速度下的20000小时L10轴承疲劳寿命。这20000小时的使用寿命没有考虑到因外部来源的轴承润滑脂污染而可能导致的特定应用寿命减少。轴、导向和键槽公差MPL-A/B15xx MPL-A/B2xx轴跳动
Do not use excessive force when fitting the cable plug with the motor connector. If the plug and connector cannot be connected together with slight hand force, realign the plane and try again. IMPORTANT The motor orientation shown is used to clearly show the alignment marks on each cable socket. The recommended motor direction during installation locates the connector at the bottom of the motor. Tip: A fully seated threaded plug leaves a small opening between the connector and the plug, approximately 1... 4 mm (0.04... 0.16 in.). NOTE: Align the keyed connector and hand tighten the recommended number of turns. If the connector cannot be tightened by hand, check that the keyed connector is correctly aligned. Do not use tools such as pliers and vises to tighten the connector. Brake and power connector feedback connector alignment plane alignment plane MP series low inertia brushless servo motor with 75 mm or smaller frame size 13 Rockwell Automation publication MP-IN006D-EN-P-2015 January Product dimensions This section provides motor dimensions. LB T L-LB D L LE F G N P LA HD AD 53.9 (2.12) LD See Detail A 2.8 ± 0.30 (0.110 ± 0.012) Shaft diameter tolerance MPL-A/B1510, - A/B1520, - A/B1530 Motor: ▸ 8.998... 9.007 (0.3543... 0.3546) MPL-A/B210, - A/B220, -A/B230 motor: Ö 10997... 11.008 (0.4330... 0.4334) detail A shaft diameter MPL-A/B 1xxx and MPL-AB2xx motor: ▸ 11.89... 11.95 (0.468... 0.470) power/brake connector feedback connector M diameter The size of the S diameter hole on the bolt circle is mm (in.) Shaft end threaded hole MPL-A/B1510, - A/B1520, - A/B1530 Motor: thread - M3 x 0.5-6H thread depth - 9.0 (0.35) MPL-A/B210, - A/B220
-A/B230 motor: thread - M4 x 0.7-6H thread depth - 10.0 (0.39) connector housing can rotate within 180 ° guide diameter tolerance MPL-A/B1510, - A/B1520, - A/B1530 motor: Ö 39.995... 40.011 (1.5746... 1.5752) MPL-A/B210, - A/B220 -A/B230 motor: ▸ 59.993... 60.012 (2.3619... 2.3627, - A/B230=4 x 4 x 16 key 14 MP series low inertia brushless servo motor, frame size 75 mm or smaller, Rockwell Automation Publication MP-IN006D-EN-P-2015 January MPL-A/B15xx and MPL-A/B2xx motor size Motor design is metric size. Inch size is an approximate conversion of mm. Dimensions without tolerance are for reference only. Motor category. No. ADmm (in.) HDmm (in.) T mm (in ）LA mm（in.。） LD（1）mm (in, and the smaller frame size is added 15 Rockwell Automation Publication MP-IN006D-EN-P-2015 January Tolerances and supplementary dimensions Motor load force rating Motor can operate under continuous axle load. The figure shows the location of radial and axial load forces, and lists the maximum value. The load is in pounds, and the kilogram is mathematical conversion. The load forces on the shaft The following table shows the 20000 hours L10 bearing fatigue under various loads and speeds life. This 20000 hour service life does not take into account the specific service life reduction that may result from contamination of bearing grease from external sources. Shaft, guide and keyway tolerance MPL-A/B15xx MPL-A/B2xx shaft runout
