MVME761EXT库存备件
1.1.9重新启动驱动器下载成功后，系统会询问您是否重新启动驱动器。如果只恢复了用户参数，通常不需要重新启动驱动器。如果ID运行结果参数已恢复，通常建议重新启动驱动器。但是，这可能取决于驱动器，因此请参阅驱动器文档。笔记重新启动驱动器会导致OPC服务器的内部断开和重新连接。这意味着清除监视器和数据记录器，从浏览的项目集中删除所有项目，关闭参数文件，折叠浏览树窗格等。重新启动驱动器需要一段时间。光标变为沙漏，状态栏通知您重新启动。参数、信号和故障4-112驱动窗口2您的DDCS网络可能根据建议进行配置，并且在节点地址1处有一个驱动器。节点地址1为备件预留。在这种情况下，如果要在另一个节点恢复驱动器的参数，则无法重新启动驱动器。您将收到一个消息框，而不是请求重新启动驱动器。如果要在这种情况下重新启动驱动器，我们建议您退出DriveWindow，或断开节点地址1处的驱动器或要重新启动的驱动器与DDCS网络的连接。然后通过关闭/打开电源手动重新启动驱动器。11.1.10如何显示错误如果在参数下载过程中遇到任何错误（例如通信错误），将显示一个包含错误列表的消息框。单击“确定”按钮确认后，也会显示警告。参数、信号和故障驱动窗口2 4-113如果您的参数文件不包含任何参数（例如，您删除了“参数”子分支），则在“选择还原类型”对话框后会出现一个消息框。如果节点地址发生更改，当DriveWindow重新启动驱动器时，您可能会收到一条错误消息，告诉您重新启动失败。如果单击“确定”按钮后，驱动器重新出现在浏览树窗格中的新节点地址，则可以忽略该消息。这是因为DriveWindow在重新连接OPC服务器之前不知道节点地址的更改。因此，它试图验证从错误的节点地址重新启动的成功。1.1.9 Restarting the Drive When the downloading has been done successfully, you are asked, whether to restart the drive or not. Restarting a drive is usually not needed in case you restored only the user parameters. If ID run result parameters were restored, restarting of the drive is usually recommended. However, this can be drive dependent, so consult the drive documentation. Note! Restarting a drive does an internal disconnecting and reconnecting of the OPC Server. This means that monitor and dataloggers are cleared, all items are removed from the browsed item set, the parameter file is closed, browse tree pane is collapsed, etc. Restarting of the drive takes for a while. The cursor turns to hour-glass and the status bar informs you about restarting. Parameters, Signals, and Faults 4-112 DriveWindow 2 Your DDCS network may be configured against recommendations and has a drive at node address one. Node address one is reserved for spare parts. In this case, if you are restoring parameters of a drive at another node, restarting of the drive cannot be done. You will get, instead of requesting restarting of the drive, a message box telling about this. If you want to restart the drive in such a case, we recommend that you either exit from DriveWindow, or disconnect the drive at node address one, or the drive to be restarted, from the DDCS network. Then restart the drive manually by power off/on. 11.1.10 How Errors are Shown If any errors (communication errors, for example) are encountered during the parameter download, a message box containing a list of errors is presented. After you have acknowledged by clicking the OK button, a warning is shown, too. Parameters, Signals, and Faults DriveWindow 2 4-113 If your parameter file does not contain any parameters (you have deleted the Parameters sub-branch, for example), you get a message box after the Select Restore Type dialog box. If the node address changes, when DriveWindow restarts the drive, you will probably get an error message, which tells you that restarting failed. If, after you click the OK button, the drive re-appears in the browse tree pane at the new node address, you may ignore the message. It is shown, because DriveWindow does not know about the node address change before re-connecting the OPC Server. Thus it tries to verify success of restarting from the wrong node address.
