P0961BC CP40B工控机器人备件
另请参阅：查看故障和事件将故障和事件联机和脱机更新项目值7.3将故障和活动联机和脱机通常，类型故障、事件、所有故障和所有事件的项目集都是联机的。这意味着经常自动更新项目集。通过更改此类项集的属性，可以更改项集的此属性。如果为“更新”属性选择“默认”，则将使用“桌面首选项”中的相应选择。但是，请注意，故障、事件、所有故障和所有事件类型项集中的故障和事件总是从设备中获取，而不是从OPC服务器的缓存中获取。实际上，DriveWindow不一定能读取所有这些文件。它只检查故障或事件记录器中的最新故障或事件，并根据结果仅读取尚未读取的故障和事件。有时您可能会遇到这样的情况，即驱动器会产生一系列故障或事件。项目集在突发期间难以读取，因为项目集不断变化。您可以将项目集（暂时）离线，以便读取故障或事件。要（临时）更改类型故障、事件、所有故障或所有事件的项目集的联机状态•在项目集窗格中，选择项目集的选项卡。•通过单击其“描述”字段仅选择第一行，或通过单击“描述”列外的全部取消选择。•单击标准工具栏中的激活/停用项目或项目集按钮，或选择“桌面”菜单中的“联机/脱机”命令。或参数、信号和故障4-76驱动窗口2项目集第一行的背景颜色发生变化，以显示新的在线状态。在线的项目集第一行有黄色背景。注意，对于类型故障和事件的项目集，更改是暂时的。当源驱动器更改时，联机状态将恢复到项目集属性中选择的状态。对于所有故障和所有事件类型的项目集，您需要自己恢复联机状态。另请参阅：查看故障和事件更新故障和事件使项目联机和脱机7.4复制故障和事件有时您可能希望将故障或事件粘贴到另一个应用程序中。为此，必须先将它们复制到剪贴板中。您还可以将它们直接拖放到另一个应用程序中。从故障、事件、所有故障或所有事件类型的项目集复制故障和事件类似于从浏览类型、用户或所有参数类型的项目集中复制或拖动项目。请注意，无法从类型故障、事件、所有故障或所有事件的项目集合中剪切故障或事件。请注意，无法将故障或事件粘贴或放置到DriveWindow中。参数、信号和故障驱动窗口2 4-77 7.4.1复制将故障、事件、所有故障或所有事件类型的项目集中的故障或事件复制到剪贴板：•在项目集窗格中，选择项目集的选项卡。•选择要从项目集中复制的故障或事件。•单击标准工具栏中的复制项目按钮，选择“编辑”菜单中的“复制”命令，或按Ctrl+C键。或上下文菜单中包含相同的“复制”命令，您可以通过在所选故障或事件之一的描述字段上单击鼠标右键获得该命令。请注意，在未选择的故障或事件的描述字段上单击鼠标右键，将取消选择所有选定的故障和事件，选择单击的故障，并显示上下文菜单。因此，操作仅涉及单击的故障或事件。选定的故障或事件将复制到剪贴板。在剪贴板中，故障和事件采用文本格式，一行中有一个故障或事件，字段由制表符分隔。请注意，剪贴板中字段的顺序不会像复制项目时那样更改。由于使用了所谓的制表符分隔格式，因此很容易将项目粘贴到外部应用程序（例如Word或Excel）中。在Excel中，字段会自动进入单独的单元格。在Word中，只需单击几下，即可制作粘贴的错误或事件的表格（选择所有粘贴的、将文本转换为表格以及可选的边框和底纹）。参数、信号和故障4-78驱动窗口2 7.4.2拖放与复制和粘贴相类似。但是，您可以将从一组类型为fault、events、all faults或all events的项目中拖动的faults和events仅放到另一个应用程序中。
See Also: Viewing Faults and Events Putting Faults and Events On-line and Off-line Updating Item Values 7.3 Putting Faults and Events On-line and Off-line Normally the item sets of type faults, events, all faults, and all events are on-line. It means that the item set is automatically updated frequently. By changing properties of such an item set you can change this property of the item set. If you select Default for the Update property, then the corresponding selection in Desktop Preferences is used. However, note that faults and events in item sets of type faults, events, all faults, and all events are always fetched from the device, never from the cache of the OPC Server. Actually DriveWindow does not necessarily read all of them. It just checks the latest fault or event in the fault or event logger and, depending on the result, reads only faults and events it has not read yet. Sometime you may encounter a situation, where a drive generates a burst of faults or events. The item set is difficult to read during the burst because the item set is constantly changing. You can to put the item set (temporarily) off-line, so you can read the faults or events. To change (temporarily) the on-line status of an item set of type faults, events, all faults, or all events • In the item sets pane, select the tab of the item set. • Select just the first line by clicking its Description field, or unselect all by clicking outside the Description column. • Either click the activate/deactivate items or item sets button in the standard toolbar, or select the Online/Offline command in the Desktop menu. or Parameters, Signals, and Faults 4-76 DriveWindow 2 The background colour of the first line of the item set changes to show the new on-line status. Item set, which is on-line, has yellow background on its first line. Note that the change is temporal for item sets of type faults and events. The on-line status is restored to the state selected in the item set properties when the source drive changes. For item sets of type all faults and all events you need to restore the on-line status yourself. See Also: Viewing Faults and Events Updating Faults and Events Putting Items On-line and Off-line 7.4 Copying Faults and Events Occasionally you may want to paste faults or events into another application. To do so, you have to copy them into the clipboard first. You can also drag and drop them directly into another application. Copying of faults and events from an item set of type faults, events, all faults, or all events is similar to copying or dragging items from an item set of type browsed, user, or all parameters. Note that it is not possible to cut faults or events from an item set of type faults, events, all faults, or all events. Note that it is not possible to paste or drop faults or events into DriveWindow. Parameters, Signals, and Faults DriveWindow 2 4-77 7.4.1 Copying To copy faults or events in an item set of type faults, events, all faults, or all events to the clipboard: • In the item sets pane, select the tab of the item set. • Select faults or events, which you want to copy from the item set. • Either click the copy items button in the standard toolbar, select the Copy command in the Edit menu, or press the Ctrl+C key. or The same Copy command is included in the context menu, which you get by clicking with the right mouse button on the description field of one of the selected faults or events. Note that clicking with the right mouse button on the description field of an unselected fault or event unselects all selected faults and events, selects the clicked one, and displays the context menu. Thus the operation concerns only the fault or event clicked. The selected faults or events are copied to the clipboard. In the clipboard, faults and events are in text format, one fault or event in a line, fields separated by tabs. Note that the order of fields in the clipboard is not changed as it would be if you were copying items. Because of the so called tab separated format used, it is easy to paste the items also into an external application, Word or Excel, for example. In Excel, the fields go automatically into separate cells. In Word you can make a table of the pasted faults or events with a few clicks (select all pasted, Convert Text to Table and, optionally, Borders and Shading). Parameters, Signals, and Faults 4-78 DriveWindow 2 7.4.2 Dragging Dragging and dropping is similar to combined copy and paste. However, you can drop faults and events dragged from an item set of type faults, events, all faults, or all events only into another application.
