PDD500A101 3BHE037649R0101工控备件模块
将参数从参数文件下载到浏览树窗格中选定的驱动器。“视图”菜单中的Ctrl+Shift+Z放大切换，与标准工具栏中的放大图形按钮相同。将趋势显示窗格置于放大模式，允许用户选择放大区域。网络菜单中的Ctrl+N网络服务器命令。显示“选择OPC服务器”对话框并连接到所选服务器，该服务器也可以位于远程PC中。网络菜单中的Ctrl+Shift+N断开服务器命令。断开当前连接的OPC服务器。Alt+F2“驱动器”菜单中的“获取控制/释放控制”命令，与“驱动器面板”工具栏中的获取/释放控制按钮相同。切换从浏览树窗格中选择的驱动器的控制状态。请注意，一次最多可以控制一个驱动器。切换控件状态会更改菜单文本。驱动器菜单中的Alt+F8重置故障命令，与驱动器面板工具栏中的重置故障按钮相同。向当前控制的驱动器发送故障重置命令。“驱动”菜单中的Shift+F9“开始”命令，与“驱动面板”工具栏中的“开始”按钮相同。向当前控制的驱动器发送启动命令。驱动器菜单中的Shift+F10停止命令，与驱动器面板工具栏中的停止按钮相同。向当前控制的驱动器发送停止命令。驱动器菜单中的Ctrl+F5反转或打开命令，与驱动器面板工具栏中的反转或关闭接触器按钮相同。向当前控制的交流或直流驱动器发送反向或接触器闭合命令。驱动器菜单中的Ctrl+F6前进或关闭命令，与驱动器面板工具栏中的前进或打开接触器按钮相同。向当前控制的交流或直流驱动器发送正向或接触器断开命令。用户界面DriveWindow 2 2-87驱动器菜单中的Ctrl+F4滑行停止命令，与驱动器面板工具栏中的滑行停止按钮相同。向当前控制的驱动器发送滑行停止命令。Ctrl+A“桌面”菜单中的“添加新项目”命令，与标准工具栏中的添加项目按钮相同。在浏览的项目集中，会显示“将项目添加到桌面”对话框，并将项目（OPC地址已给出）添加到项目集中。项目由用户命名。在用户项集中，将显示一个“添加新模板”对话框，并将给定属性的模板添加到项集中。F3“视图”菜单中的“更改格式”命令。显示一个对话框，用户可以在其中临时更改项目集中所选项目的值的显示格式，或在趋势显示窗格中用所选频道的图形光标显示的数值。如果监视器暂停，则在监视器菜单中使用Ctrl+M开始命令或继续命令，与监视器工具栏中的开始或继续监视按钮相同。开始或继续监视。
Downloads the parameters from the parameter file to the drive selected in the browse tree pane. Ctrl+Shift+Z Zoom In toggle in the View menu, same as zoom in graph button in the standard toolbar. Puts the trend display pane into zoom-in mode, which allows the user to select the zoom-in area. Ctrl+N Network Servers command in the Network menu. Presents a Select OPC Server dialog box and connects to the selected server, which can also reside in a remote PC. Ctrl+Shift+N Disconnect Server command in the Network menu. Disconnects the currently connected OPC Server. Alt+F2 Take Control/Release Control command in the Drive menu, same as take/release control button in the Drive Panel toolbar. Toggles the control status of the drive, which is selected from the browse tree pane. Note that it is possible to control at most one drive at a time. Toggling the control status changes the menu text. Alt+F8 Reset Fault command in the Drive menu, same as reset fault button in the Drive Panel toolbar. Sends fault reset command to the currently controlled drive. Shift+F9 Start command in the Drive menu, same as start button in the Drive Panel toolbar. Sends start command to the currently controlled drive. Shift+F10 Stop command in the Drive menu, same as stop button in the Drive Panel toolbar. Sends stop command to the currently controlled drive. Ctrl+F5 Reverse or On command in the Drive menu, same as reverse or close contactor button in the Drive Panel toolbar. Sends reverse or contactor close command to the currently controlled AC or DC drive. Ctrl+F6 Forward or Off command in the Drive menu, same as forward or open contactor button in the Drive Panel toolbar. Sends forward or contactor open command to the currently controlled AC or DC drive. User Interface DriveWindow 2 2-87 Ctrl+F4 Coast Stop command in the Drive menu, same as coast stop button in the Drive Panel toolbar. Sends coast stop command to the currently controlled drive. Ctrl+A Add New Item command in the Desktop menu, same as add item button in the standard toolbar. In the browsed item set presents an Add Item to Desktop dialog box and adds the item, OPC Address of which is given, into the item set. The item is named by the user. In user item sets presents an Add New Template dialog box and adds the template, properties of which are given, into the item set. F3 Change Format command in the View menu. Presents a dialog box, in which the user can temporarily change display format of the values of the selected items in the item set, or numerical values shown with the graph cursor of the selected channels in the trend display pane. Ctrl+M Start command or Continue command, if monitor is paused, in the Monitor menu, same as start or continue monitoring button in the monitor toolbar. Starts or continues monitoring.
