PFCL 301E-0.2机械备件
外壳可以安装在外壳内，或者可以安装成允许散热器延伸到外壳外部。使用1336 PLUS II用户手册（1336 PLU-5.3）中的信息帮助确定是否存在可能的外壳尺寸或降额问题。惯例为了帮助区分本手册中的参数名称和显示文本，将使用以下惯例。•参数名称将显示在[括号]中。•显示文本将显示在“引号”中。以下是本手册中使用的约定列表以及约定的定义。有关术语和定义的列表，请参阅本手册后面的术语表。辅助输入辅助输入是控制接口板上的端子连接。该连接提供了用作辅助联锁的外部输入。除非该联锁关闭，否则驱动器将出现辅助故障。辅助联锁辅助联锁是由用户提供的电路，包括复位、过载或其他联锁电路。互锁连接到驱动辅助输入。位A位是可编程逻辑中使用的单个字符或状态点。8位构成字节，16位构成字。驱动参数实际上是8位或16位字。检查检查意味着检查某物的物理状况或某些控件的设置，如参数。检查驱动板或组件也可能需要测量和测试。连接器A连接器将一个驱动板连接到另一个。连接器有两种设计，公型和母型。公连接器是固定的，包含引脚，有时通过跳线连接。母接头位于电线或带状电缆的末端，并插入公接头。1336 PLUS-6.16-2001年9月1-6简介默认当驱动器默认时，它会自动更改为预先编程的设置。启用输入启用输入是控制接口板上的端子连接。此连接提供外部输入以启用或禁用驱动输出部分。必须正确才能允许驱动器运行。False False是指逻辑错误状态。例如，当输入触点断开或未向控制接口板施加适当电压时，TB3上的控制接口信号为假。跳线跳线完成驱动板上阳连接器内两个引脚之间的电路。如果没有使用母连接器的某些可选设备，则将跳线应用于公连接器内的某些引脚，以完成特定和必要的电路。控制接口板A控制接口板插入位于主控制板下部的连接器J2和J4。该板标识为L4/4E、L5/L5E、L6/L6E、L7E、L8E或L9E，并为驱动器控制接口板提供可选的控制布线配置。参数参数是可编程的驱动器功能，用于定义驱动器的各种操作功能或状态显示。有关参数详情，请参阅公告1336 PLUSII用户手册（1336 PLU-5.3）。按下人机界面模块上的按钮以更改参数设置和驱动功能。True True是指逻辑True状态。例如，当L4/L4E触点输入闭合时，TB3上的控制接口信号为真，
enclosures may be mounted within an enclosure or may be mounted to allow the heat sink to extend outside the enclosure. Use the information in the 1336 PLUS II User Manual (1336 PLUS-5.3) to help determine if a possible enclosure sizing or derating problem exists. Conventions To help differentiate parameter names and display text in this manual, the following conventions will be used. • Parameter Names will appear in [brackets]. • Display Text will appear in “quotes”. The following is a list of conventions used throughout this manual, and definitions of the conventions. For a list of terminology and definitions, refer to the Glossary in the back of this manual. Auxiliary Input The Auxiliary Input is a terminal connection on the Control Interface Board. This connection provides an external input for use as an Auxiliary Interlock. Unless this interlock is closed, the drive will be faulted with an AuxiliaryFault. Auxiliary Interlock The Auxiliary Interlock is a user supplied circuit consisting of reset, overload, or other interlocking circuitry. The interlock is wired to the drive Auxiliary input. Bit A bit is a single character or status point used in programmable logic. Eight bits form a BYTE, 16 bits form a word. Drive parameters are actually eight bits or 16 bit words. Check To check means to examine either the physical condition of something or the setting of some control, such as a Parameter. Checking a drive board or component may also require measurements and tests. Connector A connector connects one drive board to another. Connectors come in two designs, male and female. Male connectors are stationary and contain pins, which are sometimes joined by jumpers. Female connectors are at the ends of wires or ribbon cables and plug into male connectors. 1336 PLUS - 6.16 - September, 2001 1-6 Introduction Default When a drive defaults, it automatically changes to a pre-programmed setting. Enable Input The Enable Input is a terminal connection on the Control Interface Board. This connection provides an external input to enable or disable the Drive Output section. It must be true to permit the drive to operate. False False refers to a logical false state. For instance, a Control Interface signal on TB3 is false when the input contact is open or the appropriate voltage is not applied to the Control Interface Board. Jumper A jumper completes a circuit between two pins within a male connector on a drive board. In the absence of certain optional equipment using female connectors, jumpers are applied to certain pins within a male connector to complete specific and necessary circuits. Control Interface Board A Control Interface Board plugs into connectors J2 & J4, located on the lower portion of the Main Control Board. This board is identified as L4/4E, L5/L5E, L6/L6E, L7E, L8E or L9E and provides optional control wiring configurations for a drive Control Interface Board. Parameter Parameters are programmable drive functions that define various operating functions or status displays of a drive. Refer to Bulletin 1336 PLUSII User Manual (1336 PLUS-5.3) for Parameter details. Press Press a button on the Human Interface Module to change Parameter settings and drive functions. True True refers to a logical true state. For example, a Control Interface signal on TB3 is true when: L4/L4E contact input is closed,
