PFSA101 EXCYM322001-EN模块卡件
无公差的尺寸仅供参考。电机类别。编号AD mm（in.）HD mm（in.）T mm（in..）LA mm（in.。）LD mm（in。毫米（±英寸）。D mm（in.）MPL-B…MPL-B电机类别。编号M mm（in.）S mm（in.。）此尺寸的公差为+。毫米（±英寸）。N mm（in.）P mm（in.。）GE mm（in.）F mm（in..）MPL-B…MPL-B N P LA LB T L-LB AD HD L LD GE F D LE-LE AD HD++轴端螺纹孔螺纹=M x.-H螺纹深度=M直径螺栓圆上的S直径孔导孔直径公差Ö..（..）Ö.±。M连接器外壳必须以°增量物理移除并重新定位。轴直径公差Ö..（..）键=x x轴详图，带键轴直径可选轴密封件MP系列电机轴密封套件信息请参阅第页。轴、导向器和键槽公差MPL Bxx轴跳动（T.I.R.）。导向器偏心（T.I.R）。最大端面跳动（T.I.R.）。键槽深度（GE）..（..）键槽宽度（F）。)出版物KNX-TDA-EN-P-二月Kinetix旋转运动规范MPL Bxx电机尺寸（SpeedTec DIN连接器）电机设计为公制尺寸。英寸尺寸是毫米的近似换算。无公差的尺寸仅供参考。电机类别。编号AD mm（in.）HD mm（in.）T mm（in..）LA mm（in.。）LD mm（in。毫米（±英寸）。D mm（in.）MPL-B…MPL-B电机类别。编号M mm（in.）S mm（in.。）此尺寸的公差为+。毫米（±英寸）。N mm（in.）P mm（in.。）GE mm（in.）F mm（in..）MPL-B…MPL-B N P LA LB T L-LB AD L LD GE F D LE-LE HD AD HD++S直径孔M直径螺栓圆导向直径公差
Dimensions without tolerances are for reference. Motor Cat. No. AD mm (in.) HD mm (in.) T mm (in.) LA mm (in.) LD mm (in.) If ordering an MPL-B or MPL-B motor with brake, add mm (. in.) to dimensions LD, LE, L, and LB. LE mm (in.) L mm (in.) LB mm (in.) L-LB mm (in.) Tolerance for this dimension is ±. mm (±. in.). D mm (in.) MPL-B . . . MPL-B Motor Cat. No. M mm (in.) S mm (in.) Tolerance for this dimension is +. mm (±. in.). N mm (in.) P mm (in.) GE mm (in.) F mm (in.) MPL-B . . . MPL-B N P LA LB T L-LB AD HD L LD GE F D LE - LE AD HD + + Shaft-end Threaded Hole Thread = M x .-H Thread Depth = S Diameter Holes on M Diameter Bolt Circle Pilot Diameter Tolerance Ø .. (..) Ø . ± . (. ± .) Flush to Pilot ± . Detail A See Detail A M and M connector housings can be rotated for rearward connector orientation. M connector housings must be physically removed and repositioned in ° increments. Shaft Diameter Tolerances Ø .. (..) Key = x x Shaft Detail with Key Shaft Diameter Optional Shaft Seal Refer to page for MP-Series motor shaft seal kit information. Shaft, Pilot, and Keyway Tolerances MPL-Bxx Shaft Runout (T.I.R.) . Pilot Eccentricity (T.I.R.) . Max Face Runout (T.I.R.) . Keyway Depth (GE) .. (..) Keyway Width (F) .. (..) MPL-BD, MPL-BC M Feedback Connector M Power/Brake Connector MPL-BD M Feedback Connector M Power/Brake Connector Feedback Connector Power/Brake Connector Dimensions are in mm (in.) Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications MPL-Bxx Motor Dimensions (SpeedTec DIN connectors) Motors are designed to metric dimensions. Inch dimensions are approximate conversions from millimeters. Dimensions without tolerances are for reference. Motor Cat. No. AD mm (in.) HD mm (in.) T mm (in.) LA mm (in.) LD mm (in.) If ordering an MPL-B or MPL-B motor with brake, add mm (. in.) to dimensions LD, LE, L, and LB. LE mm (in.) L mm (in.) LB mm (in.) L-LB mm (in.) Tolerance for this dimension is ±. mm (±. in.). D mm (in.) MPL-B . . . MPL-B Motor Cat. No. M mm (in.) S mm (in.) Tolerance for this dimension is +. mm (±. in.). N mm (in.) P mm (in.) GE mm (in.) F mm (in.) MPL-B . . . MPL-B N P LA LB T L-LB AD L LD GE F D LE - LE HD AD HD + + S Diameter Holes on M Diameter Bolt Circle Pilot Diameter Tolerance Ø .. (..)
