PFSA101 YM322001-ZH机械备件
出版物KNX-TDA-EN-P-二月Kinetix旋转运动规格尺寸-MP系列低惯量电机MPL-A/Bxx和MPL-A/Bsx电机尺寸（SpeedTec DIN连接器）LB T L-LB D L LE F G N P LA AD HD.LD见详图A±。（.±.）轴详图，带键轴直径公差MPL-A/B、-A/B、-A/B电机：，。（..）详图A轴直径MPL-A/B、-A/B、-A/B和MPL-A/B，-A/B，-A/B电机：Ö。动力/制动连接器反馈连接器S直径孔M直径螺栓圆尺寸单位为mm（in.）轴端螺纹孔MPL-A/B、-A/B、-A/B电机：螺纹-Mx.-H螺纹深度-MMP-A/B、-A-B、-A-B电机：螺纹-M x.H螺纹深度-。连接器外壳可在°导向直径公差范围内旋转MPL-A/B，-A/B，-A/B电机，-A/B电机：Ö..（..）轴、导向和键槽公差MPL-A/Bxx MPL-A/B xx轴跳动（T.I.R.）..导向偏心（T.I.R）..最大端面跳动（T.I.R.）..键槽深度（G）..（。。)出版物KNX-TDA-EN-P-二月Kinetix旋转运动规范MPL-A/Bxx和MPL-A/Bsx电机尺寸（SpeedTec DIN连接器）电机设计为公制尺寸。英寸尺寸是毫米的近似换算。无公差的尺寸仅供参考。电机类别。编号AD mm（in.）A/B……出版物KNX-TDA-EN-P-二月Kinetix旋转运动规范MPL-A/详图A轴直径公差S轴直径上的直径孔M直径螺栓圆。导向直径轴端螺纹孔MPL-A/B、-A/B、-A/B电机：螺纹-Mx.-H螺纹深度-MMP-A/B、-A-B电机：螺纹-M x.-H螺纹深度-ML-A/B、-A/B、-A-B电动机：螺纹-MX.-H螺纹厚度-MMP-A/B，和键槽公差MPL-A/Bxx MPL-A/B xx MPL-A/Bxx MPR-A/BxxMPL-B轴跳动（T.I.R.）
Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications Dimensions - MP-Series Low Inertia Motors MPL-A/Bxx and MPL-A/Bxx Motor Dimensions (SpeedTec DIN connectors) LB T L-LB D L LE F G N P LA AD HD . LD See Detail A . ±. (. ±.) Shaft Detail with Key Shaft Diameter Tolerances MPL-A/B, -A/B, -A/B Motors: Ø .. (..) MPL-A/B, -A/B, -A/B Motors: Ø ,. (..) Detail A Shaft Diameter MPL-A/B, -A/B, -A/B and MPL-A/B, -A/B, -A/B Motors: Ø .. (..) MPL-A/B, -A/B, -A/B = x x Key MPL-A/B, -A/B, -A/B = x x Key Optional Shaft Seal Refer to page for MP-Series small frame motor shaft seal kit information. Power/Brake Connector Feedback Connector S Diameter Holes on M Diameter Bolt Circle Dimensions are in mm (in.) Shaft-end Threaded Hole MPL-A/B, -A/B, -A/B Motors: Thread - M x .-H Thread Depth - . MPL-A/B, -A/B, -A/B Motors: Thread - M x .-H Thread Depth - . Connector housings can be rotated within a range of ° Pilot Diameter Tolerances MPL-A/B, -A/B, -A/B Motors: Ø .. (..) MPL-A/B, -A/B, -A/B Motors: Ø .. (..) Shaft, Pilot, and Keyway Tolerances MPL-A/Bxx MPL-A/Bxx Shaft Runout (T.I.R.) . . Pilot Eccentricity (T.I.R.) . . Max Face Runout (T.I.R.) . . Keyway Depth (G) .. (..) .. (..) Keyway Width (F) .. (..) .. (..) Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications MPL-A/Bxx and MPL-A/Bxx Motor Dimensions (SpeedTec DIN connectors) Motors are designed to metric dimensions. Inch dimensions are approximate conversions from millimeters. Dimensions without tolerances are for reference. Motor Cat. No. AD mm (in.) A/B . . . . Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications MPL-A/ Detail A Shaft Diameter Tolerances S Diameter Holes on Shaft Diameter M Diameter Bolt Circle. Pilot Diameter Shaft-end Threaded Hole MPL-A/B, -A/B, -A/B Motors: Thread - M x .-H Thread Depth - . MPL-A/B, -A/B Motors: Thread - M x .-H Thread Depth - MPL-A/B, -A/B, -A/B Motors: Thread - M x .-H Thread Depth - MPL-A/B, -A/B, -A/B, -B Motors: Thread - M x .-H Thread Depth - MPL-B Motors: Thread - M x .-H Thread Depth - Shaft, Pilot, and Keyway Tolerances MPL-A/Bxx MPL-A/Bxx MPL-A/Bxx MPL-A/Bxx MPL-B Shaft Runout (T.I.R.)
