PFSA145 3BSE008843R1备件模块
出版物KNX-TDA-EN-P-二月Kinetix旋转运动规格Kinetix VP食品级电机制动规格Kinetix-VP食品级发动机负载力额定值公告VPF电机能够在下表所列的最大径向或最大轴向轴负载下运行。所列径向载荷施加在轴外伸部的中间。下表表示L轴承的疲劳寿命为小时。这一小时的使用寿命并未考虑到因外部来源的轴承润滑脂污染而可能导致的特定应用寿命减少。最大运行速度受电机绕组限制。轴电机类别上的负载力。数量齿隙，最大（制动器接合）弧分钟保持扭矩N•m（lb•in）V DC A制动响应时间时的线圈电流制动转子惯性kg-m（lb•in.•s）制动电机重量，约kg（lb）释放ms接合（）ms（）通过在外部控制电路中使用二极管和齐纳二极管作为消弧装置。VPF-A/B.（）……VPF-A/B.VPF-A/B（）…VPF-A/B…VPF-A/B（）VPF-A/B..VPF-A/B（）…..VPF-A/B/VPF-A/B.（）….VPF-A/B。（）….VPF-A/B..VPF-B（）..轴伸中心施加的径向负载力轴向负载力出版物KNX-TDA-EN-P-二月Kinetix旋转运动规范Kinetix VP食品级电机（框架尺寸）径向负载力额定值（最大值）适用于非制动电机电机类别。编号（）（）.kgf=.Bf或.N。星号（*）表示在小于该列所列值的rpm值下测得的额定负载。速度，钥匙提供的VPF-A/Bxx=（+，-.）x（+，.-）x钥匙VPF-A/Bsx=（+、-.）x（+，-）x钥匙导向直径（N）轴密封完全展开键槽长度VPF-A/Bxx电机：.VPF-A/Bxx电机：.导向高度.导向高度轴密封深度.±。编码器绝对位置的（.±.）旋转停止°±°轴端标记（或键）方向=.VPF-A/Bxx电机：螺纹-M x.-H螺纹深度-出版物KNX-TDA-EN-P-二月Kinetix旋转运动规范VPF-A/Bxx、VPF-A/B/xx、VPF-3/Bxx和VPF-Bxx电机尺寸（SpeedTec DIN连接器）电机设计为公制尺寸。英寸尺寸是毫米的近似换算。无公差的尺寸仅供参考。
Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications Kinetix VP Food Grade Motor Brake Specifications Kinetix VP Food Grade Motor Load Force Ratings Bulletin VPF motors are capable of operating with the maximum radial or maximum axial shaft loads listed in the following tables. Radial loads listed are applied in the middle of the shaft extension. The tables starting below represent an L bearing fatigue life of , hours. This ,-hour life does not account for possible application-specific life reduction that can occur due to bearing grease contamination from external sources. Maximum operating speed is limited by motor winding. Load Forces on Shaft Motor Cat. No. Backlash, max (brake engaged) arc minutes Holding Torque N•m (lb•in) Coil Current at V DC A Brake Response Time Brake Rotor Inertia kg-m (lb•in•s ) Brake Motor Weight, approx kg (lb) Release ms Engage () ms () By using diode and zener diode as arc suppression device in external control circuit. VPF-A/B . () .. . . VPF-A/B . . VPF-A/B . () .. . . VPF-A/B . . VPF-A/B . () .. . . VPF-A/B . . VPF-A/B . . VPF-A/B . () .. . . VPF-A/B . () .. . . VPF-A/B . . VPF-B . () .. . . Radial Load Force Applied at Center of Shaft Extension Axial Load Force Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications Kinetix VP Food Grade Motors ( frame size) Radial Load Force Ratings (maximum) for Non-brake Motors Motor Cat. No. () () . kgf = . lbf or . N. An asterisk (*) indicates a load rating measured at an rpm value that is less than the value listed for that column. Speed, Key Supplied VPF-A/Bxx = (+, -.) x (+, -.) x Key VPF-A/Bxx = (+, -.) x (+, -.) x Key Pilot Diameter (N) Shaft Seal Fully Developed Keyway Length VPF-A/Bxx Motors: . VPF-A/Bxx Motors: . Pilot Height . Pilot Height Shaft Seal Depth . ±. (. ±.) Rotational Stop ° ±° Shaft-end mark (or key) orientation for encoder absolute position = . VPF-A/Bxx Motors: Thread - M x .-H Thread Depth - . Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications VPF-A/Bxx, VPF-A/Bxx, VPF-A/Bxx, and VPF-Bxx Motor Dimensions (SpeedTec DIN connectors) Motors are designed to metric dimensions. Inch dimensions are approximate conversions from millimeters. Dimensions without tolerances are for reference.
