PFSK102/YM322001-EG工业备件
使用下面的目录编号表图表了解电机的配置。有关产品可用性的问题，请联系您的Allen-Bradley分销商。（）额定速度等级仅用于比较目的。在Kinetix驱动系统设计指南（KNX-RM出版物）中，使用运动分析仪软件为您的应用程序和/或扭矩/速度曲线确定大小和选择电机。（）并非所有组合都可用。只有第页Kinetix VP连续工作电机性能规范中列出的额定速度和磁体堆长度配置可用。使用运动分析仪软件为您的应用确定电机的大小和选择电机。VP C-B xxx x x-x x x F S工厂选项S=轴封，标准（IP）冷却F=强制通风制动器=无制动器=V DC制动器轴键J=轴键K=光滑轴连接器=单SpeedTec DIN连接器，直角，°可旋转=SpeedTec DIN-连接器，直角，°旋转额定转速（）（）=rpm A=rpm D=rpm磁体堆叠长度（，，堆叠）（）框架尺寸-螺栓圆直径（BCD/轴高度（SH）=IEC mm BCD/SH mm=IEC mm BC/SH mm=IEC mm BCD/SH mm电压等级B=V系列C型=连续负载系列VP=根据Kinetix驱动额定值优化的永磁旋转伺服电机反馈S=sin/cos，绝对单圈编码器（Hiperface协议）Q=位绝对多圈数字编码器，SIL/PLd等级，-位二级安全通道（Hiperface DSL协议）Y=-位绝对多匝数字编码器（EnDat数字协议）出版物KNX-TDA-EN-P-二月Kinetix旋转运动规范Kinetix VP连续工作电机高分辨率编码器Kinetix VP-连续工作电机可配备高性能编码器，可选择单匝（-S）和多匝（-Q或-Y）高分辨率反馈：采用Hiperface协议的VPC-Bxxxxx-S电机–每转sin/cos循环，最高分辨率为位（，，每转计数），采用HiperfaceDSL协议的绝对单圈编码器VPC-Bxxx-Q电机–每圈计数，最高分辨率位，绝对多圈数字编码器，匝数–SIL/PLd额定值，-位二级安全通道-数字双线通信集成到具有EnDat数字协议的单电机电力电缆VPC-Bxxxxx-Y电机中-位分辨率高达
Use the catalog numbering table chart below to understand the configuration of your motor. For questions regarding product availability, contact your Allen-Bradley distributor. () Rated speed hierarchy is only for comparative purposes. Use Motion Analyzer software to size and select motors for your application, and/or the torque/speed curves in the Kinetix Drive System Design Guide, publication KNX-RM. () Not all combinations are available. Only the configurations for rated speed and magnet stack length, as listed in Kinetix VP Continuous Duty Motor Performance Specifications on page are available. Use Motion Analyzer software to size and select motors for your application. VP C - B xxx x x - x x x x F S Factory Options S = Shaft seal, standard (IP) Cooling F = Forced ventilation Brake = No brake = V DC brake Shaft Key J = Shaft key K = Smooth shaft Connectors = Single SpeedTec DIN connector, right angle, ° rotatable = SpeedTec DIN connector, right angle, ° rotatable Rated Speed () () = rpm A = rpm D = rpm Magnet Stack Length (, , , , stacks) () Frame Size - Bolt Circle Diameter (BCD / Shaft Height (SH) = IEC mm BCD / SH mm = IEC mm BCD / SH mm = IEC mm BCD / SH mm Voltage Class B = V Series Type C = Continuous Duty Series VP = Permanent magnet rotary servo motors that are optimized to Kinetix drive ratings Feedback S = sin/cos, absolute single-turn encoder (Hiperface protocol) Q = -bit absolute multi-turn digital encoder, SIL/PLd rated, -bit secondary safety channel (Hiperface DSL protocol) Y = -bit absolute multi-turn digital encoder (EnDat digital protocol) Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications Kinetix VP Continuous Duty Motor High Resolution Encoders Kinetix VP continuous-duty motors are available with high-performance encoders with a choice of single-turn (-S) and multi-turn (-Q or -Y) high-resolution feedback: VPC-Bxxxxx-S motors with Hiperface protocol – sin/cos cycles per revolution for up to -bit resolution (,, counts per revolution), absolute single-turn encoder VPC-Bxxxxx-Q motor with Hiperface DSL protocol – -bit resolution for up to ,, counts per revolution, absolute multi-turn digital encoder, turns – SIL/PLd rated, -bit secondary safety channel – Digital two-wire communication integrated into the single motor-power cable VPC-Bxxxxx-Y motors with EnDat Digital protocol – -bit resolution for up to
