PFSK10385389091 YM322001-BZ备件库存
先导安全阀直径VPL-A/Bxx电机=。VPL-A/Bxx电机=。VPL-A/Bxx电机=。VPL Bxx电机=。键槽长度VPL-A/Bxx=。VPL-A/Bxx=。VPL-A/Bxx=。VPL Bxx=。先导直径（N）先导安全阀直径轴肩齐平至先导高度±。飞行员高度VPL-A/Bxx=。VPL-A/Bxx=。VPL-A/Bxx=。VPL Bxx=。密封面VPL-A/Bxx=。（）VPL-A/Bxx=。（）VPL-A/Bxx=。（）VPL Bxx=。（）导向卸压高度（T）导向高度导向直径公差VPL-A/Bxx电机：Ö..（。（±.）（）公差为±。VPL-BD电机的（±.）M连接器（需要AWG电缆）。M接头，用于所有其他Bulletin VPL电机。VPL Bxx电机电机类别上的电机接头。编号M连接器VPL Bx VPL BxVPL Bx-VPL-BB M连接器VPL-BD°±°轴端标记（或键）编码器绝对位置方向=。出版物KNX-TDA-EN-P-二月Kinetix旋转运动规范VPL-A/Bxx、VPL-A/Bsx、VPL-A/B xx和VPL-Bxx电机尺寸（SpeedTec DIN连接器）电机设计为公制尺寸。英寸尺寸是毫米的近似换算。无公差的尺寸仅供参考。电机类别。编号ADmm（in.）HDmm（in。mm（英寸）至尺寸L、LB、LE和LD。如果订购带制动器的VPL-a/Bxx-xxxxxx电机，请添加。mm（英寸）至尺寸L、LB、LE和LD。如果订购带制动器的VPL-a/Bxx-xxxxxx电机，请添加。mm（英寸）至尺寸L、LB、LE和LD。如果订购带制动器的VPL-Bxx-xxxxxx电机，请添加。mm（英寸）至尺寸L、LB、LE和LD。LE（）mm（in.）L（）mm。mm（±英寸）.D（）mm（英寸）（）键槽、轴直径和导向直径公差，请参阅第页。M毫米（英寸）S毫米（英寸
Pilot Relief Diameter VPL-A/Bxx Motors = Ø . VPL-A/Bxx Motors = Ø . VPL-A/Bxx Motors = Ø . VPL-Bxx Motors = Ø . Keyway Length VPL-A/Bxx = . VPL-A/Bxx = . VPL-A/Bxx = . VPL-Bxx = . Pilot Diameter (N) Pilot Relief Diameter Shaft Shoulder Flush to Pilot Height ±. Pilot Height VPL-A/Bxx = . VPL-A/Bxx = . VPL-A/Bxx = . VPL-Bxx = . Sealing Surface VPL-A/Bxx = . () VPL-A/Bxx = . () VPL-A/Bxx = . () VPL-Bxx = . () Pilot Relief Height (T) Pilot Height Pilot Diameter Tolerances VPL-A/Bxx Motors: Ø .. (..) VPL-A/Bxx Motors: Ø .. (..) VPL-A/Bxx Motors: Ø .. (..) VPL-Bxx Motors: Ø .. (..) () Tolerance is ±. (±.) () Tolerance is ±. (±.) M connectors (requires AWG cable) for VPL-BD motors. M connectors for all other Bulletin VPL motors. Motor Connectors on VPL-Bxx Motors Motor Cat. No. M Connector VPL-Bx VPL-Bx VPL-Bx VPL-BB M Connector VPL-BD ° ±° Shaft End Mark (or Key) Orientation for Encoder Absolute Position = . Publication KNX-TDA-EN-P - February Kinetix Rotary Motion Specifications VPL-A/Bxx, VPL-A/Bxx, VPL-A/Bxx, and VPL-Bxx Motor Dimensions (SpeedTec DIN connectors) Motors are designed to metric dimensions. Inch dimensions are approximate conversions from millimeters. Dimensions without tolerances are for reference. Motor Cat. No. ADmm (in.) HDmm (in.) T mm (in.) LA mm (in.) LD () mm (in.) () If ordering a VPL-A/Bxx-xxxxx motor with brake, add . mm (. in.) to dimensions L, LB, LE, and LD. If ordering a VPL-A/Bxx-xxxxx motor with brake, add . mm (. in.) to dimensions L, LB, LE, and LD. If ordering a VPL-A/Bxx-xxxxx motor with brake, add . mm (. in.) to dimensions L, LB, LE, and LD. If ordering a VPL-Bxx-xxxxx motor with brake, add . mm (. in.) to dimensions L, LB, LE, and LD. LE () mm (in.) L () mm (in.) LB () mm (in.) L-LB () mm (in.) () Tolerance for this dimension is ±. mm (±. in.). D () mm (in.) () For keyway, shaft diameter, and pilot diameter tolerances, refer to page . M mm (in.) S mm (in.) N () mm (in.) P mm (in.) GE () mm (in.) F
