PFSK164 3BSE021180R1工控机器人备件
清洁地板，并使用沉头螺钉将垫子和边缘装饰件固定到位，以适应应用。安装周边装饰件时，确保装饰件和地板之间或顶部和底部之间（取决于装饰件类型）没有任何电线被夹住或压碎。如果电线可能被夹住或拉动，应在电线离开周边装饰的地方使用应变消除夹。所有电线应采用适当的导管进行保护。如果可能，电线/导管不应穿过可能会绊倒的地板区域。如果无法避免这种情况，应将电线/导管封装在我们的《保护电线指南》440F-T3230中（参见第37页的可用备件）。6.2控制单元的安装和布线（也可参考第4节图7、第5.3.7节和第5.7节）控制单元应按照供应进行安装。除本手册所述的程序或连接外，不得对其进行修改或进行任何其他程序或连接。通过小心敲击（440F-C4000P）或钻出（440F-C4 000S，440FC28013）要使用的电缆入口位置来准备控制单元。输入电源必须单独布线，并通过与输出接线所用电源的单独入口进入控制单元。将控制单元安装在其计划位置。控制单元端子的所有接线必须使用提供的导线类型或多股导管电缆/开关设备电缆/设备导线，导线为0.5-1.5mm2。电缆进入控制单元（440F-C4000P、440F-C400S和440F-C28013）时，必须使用防护等级为IP65的压盖或适配器。确保压盖或适配器的尺寸合适并完全拧紧。必须使用提供的绝缘针脚压褶。这种电线和端子组合避免了因过度拧紧或振动而导致的松股短路或开路的可能性。确保使用合适的棘轮型压接工具。压接导线和绝缘层。不要将多条电线连接到一个压接上。确保电源在第6.4节之前保持隔离和锁定。主交流电源必须在供电点通过最大500mA的高断裂容量（HRC）保险丝进行外部熔断。除非电源的中性侧参考接地，否则必须按照相同的规范进行熔断。28图26 440F-C4000P和440F-C400S（按照步骤1-12进行正确安装-参见以下页面）N/O PB R IND MC MC 31 32 13 14 23 24 1 2 3 4–ve+ve N L A M 230 110 LED指示灯辅助保险丝500mA主保险丝500mA远程复位端子远程复位指示端子接触器4 23 MC MC IND R PB NO NL+ve–ve 110V 230V自动复位手动复位24V N/C辅助端子N/O辅助端子安全输出端子N/C监控输出端子接触器监控端子远程复位端子MAT 1 MAT 2 MAT 3 MAT 4 MAT 5 MAT 6 MAT 7 MAT 8远程复位指示端子3 4 6 5 7 9 8 10 4 1 2 11模式设置手动自动电压设置110V 230V 24V日期勾选框图27 440F-C4000D（按照步骤1-12正确安装）1。使用110V或230VAC时
Clean off the floor and fix the mats and edge trim in place using countersunk screws to suit the application. As the perimeter trim is fitted ensure none of the wiring is trapped or crushed between the trim and the floor or the top and bottom sections (depending on trim type). If there is a possibility that the wires may be caught or pulled, a strain relief clamp should be used where the wiring exits the perimeter trim. All wiring should be protected in suitable conduit. If possible, the wiring/conduit should not cross a floor area where it will be a tripping hazard. If it is not possible to avoid this, the wiring/conduit should be enclosed within our Protective Wire Guide 440F-T3230 (see Available Spares on page 37). 6.2 CONTROL UNIT INSTALLATION AND WIRING (also refer to section 4 fig. 7, section 5.3.7 and section 5.7) The control unit should be installed as supplied. It must not be modified or subjected to any procedures or connections other than those described in this manual. Prepare the control unit by carefully knocking out (440F-C4000P) or drill out (440F-C4000S, 440FC28013) the cable entry positions to be used. The input power supply must be separately routed and enter the control unit via a separate entry to those used for the output wiring. Mount the control unit in its planned position. All wiring to the control unit terminals must use either wire type supplied or multistrand conduit cable/ switchgear cable/ equipment wire with 0.5 - 1.5mm2 conductors. Cable entry into the control unit (440F-C4000P, 440F-C4000S & 440F-C28013) must be achieved using glands or adaptors which provide an ingress protection rating of IP65. Ensure that the glands or adaptors are of a suitable size and are fully tightened. The insulated pin crimps supplied must be used. This wire and terminal combination avoids the possibility of shorts from loose strands or open circuits caused by overtightening or vibration. Ensure that a suitable ratchet type crimp tool is used. Crimp onto both the conductor and the insulation. Do not connect more than one wire onto one crimp. ENSURE THAT THE POWER SUPPLY REMAINS ISOLATED AND LOCKED OFF UNTIL SECTION 6.4. The mains AC supply must be externally fused at the point of supply by a 500mA max. high rupture capacity (HRC) fuse. Unless the neutral side of the supply is referenced to earth, it must be fused to the same specification. 28 Fig. 26 440F-C4000P and 440F-C4000S (Follow steps 1-12 for correct installation - see following pages) N/O PB R IND MC MC 31 32 13 14 23 24 1 2 3 4 –ve +ve N L A M 230 110 LED INDICATORS SECONDARY FUSE 500mA PRIMARY FUSE 500mA REMOTE RESET TERMINALS REMOTE RESET INDICATION TERMINALS CONTACTOR 4 23 MC MC IND R PB NO NL +ve –ve 110V 230V AUTO RESET MANUAL RESET 24V N/C AUXILIARY TERMINALS N/O AUXILIARY TERMINALS SAFETY OUTPUT TERMINALS N/C MONITORED OUTPUT TERMINALS CONTACTOR MONITORING TERMINALS REMOTE RESET TERMINALS MAT 1 MAT 2 MAT 3 MAT 4 MAT 5 MAT 6 MAT 7 MAT 8 REMOTE RESET INDICATION TERMINALS 3 4 6 5 7 9 8 10 4 1 2 12 11 Mode set MANUAL AUTO Voltage set 110V 230V 24V Date tick boxes Fig. 27 440F-C4000D (Follow steps 1-12 for correct installation) 1. When using a 110V or 230VAC
