PFTL101B 2.0KN 3BSE004185R1工控机器人备件
对于一个接触器，使用连接端子14和23的端子13和24。对于具有两个独立控制电路（即双通道系统）的两个接触器，使用13和14连接到一个接触器控制电路，使用23和24连接到另一个接触器。参见图。14/15和16/17，用于与机器控制电路的典型接口示例。注意：安全输出应通过硬接线直接连接到机器主控制元件（接触器）。它们不得通过任何元件连接，例如普通继电器、PLC等，这些元件未适当指定用于安全相关功能。7.接触器监控：控制单元配有这些连接的端子。当链路被移除时，它们可以连接到机器接触器上的正向导向N/C辅助触点，以监控双通道控制系统中的接触器。如果一个接触器在其控制线圈断电时未能隔离电源，则在故障排除之前，垫控制单元将不允许另一个接触器通电。8.远程复位：N/O-这些端子用于连接远程复位按钮。这必须是一个N/O瞬时按钮装置，其位置应能提供检测区域的全貌。仅限440F-C4000P、440F-C4000 S、440F-C28013。如果从控制单元上看不到危险区域的全貌，请断开接线盒上控制单元盖上的复位开关的电线，以禁用控制单元的复位功能。9.远程复位指示：如果与发光的按钮远程复位开关一起使用，将显示何时需要复位垫子系统。这些端子用于连接灯泡（28V）。32 MAT 1 MAT 2 MAT 3 MAT 4 MAT 5 MAT 6 MAT 7短接插头MAT 8 10.手动复位/自动复位：M/A开关。将M/A开关设置为所需设置。M=手动复位模式A=自动复位模式。11.根据建立的电压和模式设置标记并签署标签。12.标记为1至8的八个六通接头。这些接头是控制单元的垫连接，并连接到单元外部的外部快速连接插头。13.重新检查接线连接，包括机器控制系统接线的连接或修改。更换盖。将盖固定在相关单元上。
For ONE CONTACTOR use terminals 13 & 24 with terminals 14 & 23 linked. For TWO CONTACTORS with two independent control circuits (i.e. a dual channel system), use 13 & 14 for connection to one contactor control circuit and 23 & 24 to the other. See figs. 14/15 and 16/17 in section 5 for examples of typical interfacing with the machine control circuit. NOTE: The safety outputs should be connected directly via hard wiring to the machine primary control elements (contactors). They must not be connected via any elements e.g. ordinary relays, PLCs, etc. not suitably specified for safety related functions. 7. CONTACTOR MONITORING: The control unit is provided with these terminals linked. When the link is removed they can be connected to positively guided N/C auxiliary contacts on the machine contactors to provide monitoring of the contactors in dual channel control systems. If one contactor fails to isolate the power at de-energisation of its control coil the mat control unit will not allow the other contactor to be energised until the fault has been rectified. 8. REMOTE RESET: N/O - These terminals are provided for the connection of a remote reset button. This MUST be a N/O momentary push button device positioned at a location which gives a full view of the detection zone. 440F-C4000P, 440F-C4000S, 440F-C28013 only. If there is not also a full view of the hazard zone from the control unit, disconnect the wires from the reset switch on the control unit lid at the terminal block to disable the reset function at the control unit. 9. REMOTE RESET INDICATION: If this is used in conjunction with an illuminated push button remote reset switch, it will show when the mat system needs to be reset. These terminals are for connection to the bulb (28V). 32 MAT 1 MAT 2 MAT 3 MAT 4 MAT 5 MAT 6 MAT 7 Shorting Plug MAT 8 10. MANUAL RESET / AUTO RESET: M/A SWITCH. Set the M/A switch to the required setting. M = MANUAL RESET MODE A = AUTO RESET MODE. 11. Mark and sign the label according to the Voltage and Mode settings established. 12. Eight six-way connectors labeled 1 to 8. These are the mat connections into the control unit and are connected to the external quick connect plugs on the outside of the unit. 13. Re-check the wiring connections including connections or modifications made to the machine control system wiring. Replace lid. Secure lid on relevant units.
