PFTL101B 2.0KN 3BSE004191R1工控模块卡件
包括保护接地。检查电压选择开关的设置，参见步骤1。不要与步骤3所示的端子进行任何连接。保护接地线的尺寸应至少与电源线的尺寸相同。3.如果使用24VAC/DC电源，应将其连接至所示端子，确保极性正确。不要与步骤2所示的端子进行任何连接。对于24VAC，电源的接地极应连接到-ve端子。4.垫子连接：将垫子的引线连接到所示的端子。1=白色，2=白色，3=黑色，4=黑色。440F-C28013-八个标有1至8的快速连接适配器位于装置底座上，并提供与垫子的连接。31 A1•+重置IND 1 2 MC Y1 Y3 Y5••13 23 31 L N 110/230V AC电源A2-重置IND 3 4 MC Y2 Y4 Y6••14 24 32 110/230V VAC可选24V AC/DC 24V AC/DC电源接触器控制电源辅助可选远程指示装置电源绿色自动重置模式绿色手动重置模式绿色机器启用绿色白色黑色白色Y1Y2 Y4Y5Y6保险丝更换向上110V电源向下230V电源500 mAT自动1手动2 3 4 5 11 8 9 67 10模式设置电压设置手动自动日期110v 230V 24v勾选框将垫子连接到440F-C28013控制单元图27a终止未使用的垫子连接和连接垫子如果要连接到控制单元的垫子少于8个，则必须使用提供的短路插头终止其他连接。所需的垫子应按顺序（1至8）连接到装置外部的快速连接适配器。如图27a所示，通过断开安装的连接器并更换短路插头来终止未使用的连接器。5.辅助输出：该端子提供适用于指示或报警装置的辅助N/C触点（即，当机器启用灯关闭时闭合）。它们不能连接到安全电路。注：MGCSM1和MGCSM4提供N/C和N/O触点。6.安全输出：这些是用于连接到机器安全电路的无电压端子，即，它们与机器接触器控制电路（最大额定值250V 4A）串联连接。应使用额定值适当的保险丝对其进行外部保护。
including a protective earth, to the terminals shown. Check setting on voltage selector switch, see step 1. Do not make any connections to the terminal shown at step 3. The size of the protective earth wire should be at least equal to that of the supply wire. 3. If a 24VAC/DC supply is being used it should be connected to the terminals shown, ensuring correct polarity. Do not make any connections to the terminals shown at step 2. With 24VAC the earthed pole of the power supply should be connected to the –ve terminal. 4. MAT CONNECTIONS: Connect the leads from the mat to the terminals shown. 1=WHITE, 2=WHITE, 3=BLACK, 4=BLACK. 440F-C28013 - eight quick connect adaptors labelled 1 to 8 are located on the base of the unit and provide connection to the mats. 31 A1 • + RESET IND 1 2 MC Y1 Y3 Y5 • • 13 23 31 L N 110/230V AC SUPPLY A2 -- RESET IND 3 4 MC Y2 Y4 Y6 • • 14 24 32 110/230VAC selectable 24V AC/DC 24V AC/DC SUPPLY CONTACTOR CONTROL POWER AUXILIARY OPTIONAL REMOTE INDICATION UNIT POWER GREEN AUTO RESET MODE GREEN MANUAL RESET MODE GREEN MACHINE ENABLED GREEN WHITE BLACK BLACK WHITE Y1Y2 Y3 Y4Y5Y6 Fuse replacement UP 110V SUPPLY DOWN 230V SUPPLY 500 mAT AUTOMATIC 1 MANUAL 2 3 4 5 11 8 9 67 10 Mode set Voltage set MANUAL AUTO Date 110v 230v 24v tick boxes Connecting the mats to 440F-C28013 control unit Fig. 27a Terminating unused mat connections and connecting mats If less than 8 mats are to be connected to the control unit, the other connections must be terminated with the shorting plugs supplied. The required mats should be connected in sequence (1 to 8) to the quick connect adaptors located on the outside of the unit. Terminate unused connectors by un-plugging fitted connectors and replacing with shorting plugs as shown in Fig. 27a. 5. AUXILIARY OUTPUTS: This terminal provides auxiliary N/C contacts (i.e. Closed when the MACHINE ENABLED light is OFF) suitable for indication or alarm devices. THEY MUST NOT BE CONNECTED TO THE SAFETY CIRCUIT. NOTE: MGCSM1 and MGCSM4 offer N/C and N/O contacts. 6. SAFETY OUTPUTS: These are volt free terminals for connection to the machine safety circuit i.e.. They are connected in series with the machine contactor control circuit (max rating 250V 4A). They should be externally protected by a suitably rated fuse(s).
