PFTL101B 3BSE004203R1系统模块卡件
5.8最终传感器垫布局考虑到这些因素后，现在可以检查并最终确定传感器垫布局。考虑机器响应时间是否与初始计算有所不同。在可能的情况下，应在检测区的外侧边缘设置垫子和电线。这简化了安装和更换（如果需要），并且所有布线都受到周边装饰的保护。5.9布线所有系统布线必须防止机械损坏，并适当密封以适应操作环境。提供防水对接接头用于垫子到垫子的连接，并由边缘镶边保护。如果需要在地板上布线，440F-T3230导线导管可以提供适当的保护。其他电线线路应使用导管或线槽。控制单元的密封完整性必须通过使用尺寸正确且紧固的导管配件或电缆压盖保持在IP65。布线实践必须符合EN 60204-1第14条的要求。注意：为了确保110/230V电源的隔离，输入电源必须单独布线，并通过用于输出接线的单独配件或压盖进入控制单元。从控制单元到垫子的电线可以使用导管埋在地板中，或通过边缘装饰件。此类安装建议使用挠性导管。详见第6节。确定接线方法，并确定控制单元接线垫的输入和输出连接点。5.10最终细节准备安装布局和电路的工作计划和图纸。建议将所有测量和计算记录并保存在机器的技术文件中。25第6节-安装和调试开始安装前，应完整阅读本手册。开始工作前，请仔细学习本节内容。安装和调试应由系统设计师监督。需要一名熟悉工业布线实践的机械技术人员和一名电工进行安装。
5.8 FINAL SENSOR MAT LAYOUT Having considered these factors, the sensor mat layout can now be checked and finalised. Consider whether the machine response time has changed from the initial calculations. Whenever possible, mats should be arranged with the wires at the outside edge of the detection zone. This simplifies installation and replacement if required and all wiring is protected by the perimeter trim. 5.9 WIRING All system wiring must be protected from mechanical damage and suitably sealed for the operating environment. Waterproof butt connectors are supplied for mat to mat connections and are protected by the edge trim. Where wire runs are required across the floor, the 440F-T3230 wire guide can provide suitable protection. Conduit or trunking should be used for other wire runs. The sealing integrity of the control unit must be maintained by the use of correctly sized and tightened conduit fittings or cable glands to IP65. Wiring practices must be in accordance with EN 60204-1 Clause 14. NOTE: In order to ensure the isolation of the 110/230V supply, the input power supply must be separately routed and enter the control unit via separate fittings or glands to those used for the output wiring. Wiring from the control unit to the mat may be buried in the floor using conduit, or pass via the edge trim. Flexible conduit is recommended for this type of installation. See section 6 for further details. Determine the wiring method and determine the input and output connection points for the mat to control unit wiring. 5.10 FINAL DETAILS Prepare a work schedule and drawings of the installation layout and the electrical circuit. It is recommended that all measurements and calculations are recorded and retained in the technical file for the machine. 25 Section 6 - INSTALLATION AND COMMISSIONING This manual should be read in full before commencing installation. Study this section completely before starting work. The installation and commissioning should be supervised by the system designer. A mechanical technician and an electrician familiar with industrial wiring practices will be required to undertake the installation.
