PFTL201CE 50.0KN 3BSE007913R51输入输出模块
以装饰件上的孔为导向，标记并钻孔地板（必要时安装塞子）。清洁地板，并使用沉头螺钉将垫子和边缘装饰件固定到位，以适应应用。安装周边装饰件时，确保装饰件和地板之间或顶部和底部之间（取决于装饰件类型）没有任何电线被夹住或压碎。如果电线可能被夹住或拉动，应在电线离开周边装饰的地方使用应变消除夹。所有电线应采用适当的导管进行保护。如果可能，电线/导管不应穿过可能会绊倒的地板区域。如果无法避免这种情况，接线/导管应封装在保护导线指南440F-A3230 6.2控制单元安装和接线中。控制单元应按照供应进行安装。除本手册中所述的程序或连接外，不得对其进行修改或进行其他程序或连接。将控制单元安装在其计划位置。控制单元的所有接线都通过Harting接头。主交流电源必须在供电点通过最大500 mA高断裂容量（HRC）保险丝进行外部熔断。除非电源的中性侧参考接地，否则必须按照相同的规范进行熔断。确保电源保持隔离和锁定，直到第6.4节建议的用于进入电缆槽的垫线的切口（周边装饰件的底部）建议的用于柔性导管入口的切口用于440F-T3*11通道装饰件使用带有柔性导管的应变消除夹。柔性导管应力消除夹在此处切割槽在锋利边缘上使用边缘垫圈用于440F-T3*10标准饰件注意事项440F MatGuard™ Mat Manager用户手册第6节-安装和调试28罗克韦尔自动化出版物95302194/EO:0240发行号：8）6.2.1 440F-C28011和440F-C2801 2–12针Brad Harrison连接注：440F-C28022安全输出上的新端子连接下表显示了440F-C28031和440F-328012的直型配合电缆。其他信息和其他配套电缆可在传感器目录中找到。440F-C28011引脚电线颜色控制器连接安全输出1 1橙色53 6橙色w/黑色迹线54安全输出2 2蓝色63 7蓝色w/黑色迹线64辅助输出4红色w/黑色轨迹线81 10红色82监控电路3白色w/黑色线MCa 8黑色w/白色迹线MCb电源11白色-ue 12黑色+ue接地9绿色GND/E 440F-C2801 2引脚电线颜色控制连接安全输出橙色53 4红色w/黑色痕迹54安全输出
Using the holes in the trim as a guide, mark out and drill the floor (fit plugs if required). Clean off the floor and fix the mats and edge trim in place using countersunk screws to suit the application. As the perimeter trim is fitted ensure none of the wiring is trapped or crushed between the trim and the floor or the top and bottom sections (depending on trim type). If there is a possibility that the wires may be caught or pulled, a strain relief clamp should be used where the wiring exits the perimeter trim. All wiring should be protected in suitable conduit. If possible, the wiring/conduit should not cross a floor area where it will be a tripping hazard. If it is not possible to avoid this, the wiring/conduit should be enclosed within Protective Wire Guide 440F-A3230 6.2 Control Unit Installation and Wiring The control unit should be installed as supplied. It must not be modified or subjected to procedures or connections other than those described in this manual. Mount the control unit in its planned position. All wiring to the control unit is through the Harting connector. The mains AC supply must be externally fused at the point of supply by a 500 mA max. high rupture capacity (HRC) fuse. Unless the neutral side of the supply is referenced to earth, it must be fused to the same specification. Ensure that the power supply remains isolated and locked off until section 6.4 Suggested cut-out for mat wires entering cable trunk (base of perimeter trim) Suggested cut-out for flexible conduit entry For 440F-T3*11 Channel Trim Use strain relief clamp with flexible conduit. Flexible Conduit Strain Relief Clamp Cut slots here Use edge grommets over sharp edges For 440F-T3*10 Standard Trim ATTENTION 440F MatGuard™ Mat Manager User Manual Section 6 - Installation and Commissioning 28 Rockwell Automation Publication 95302194/EO:0240 Issue No: 8) 6.2.1 440F-C28011 and 440F-C28012 – 12-pin Brad Harrison Connections Note: New Terminal connection on the Safety Outputs of 440F-C28012 The following table shows straight style mating cables for the 440F-C28011 and 440F-C28012. Additional information and other mating cables can be found in the Sensors catalog. 440F-C28011 Pin Wire Color Controller Connection Safety Output 1 1 Orange 53 6 Orange w/ Black Trace 54 Safety Output 2 2 Blue 63 7 Blue w/Black Trace 64 Auxiliary Output 4 Red w/ Black Trace 81 10 Red 82 Monitoring Circuit 3 White w/ Black Trace MCa 8 Black w/ White Trace MCb Power 11 White -ue 12 Black +ue Ground 9 Green GND / E 440F-C28012 Pin Wire Color Controller Connection Safety Output 1 1 Orange 53 4 Red w/ Black Trace 54 Safety Output
