PM210 3BSE021386R2工控模块机器人备件
.<1 ms响应时间效率91%，典型散热（BTU/hr）10 kVA型号：3798@208V，220V输入6294@480V和600V（带输入隔离变压器）15 kVA型号：5122@208V和220V输入8134@480V和600V（带有输入隔离变压器，免维护电池运行时间参见电池备份时间表电池更换现场可更换充电器默认值为每个电池串3.4A。充电器电流可配置为每串0.5A至25A，总最大值为34A（受输入电流限制）电池启动允许在无公用电输入的情况下启动UPS通用诊断启动时全系统自检UPS旁路过载或UPS故障时自动并联冗余是，使用Powerware热同步技术和容量尺寸和重量请参阅型号选择表过载（正常运行）150%持续5秒/125%持续1分钟（在线），110%持续10分钟通信LCD显示屏带有蓝色背光LED的图形LCD（4）用于通知和警报的LED声音警报是通信端口（1）RS-232，（1）继电器触点，（2）环境输入通信插槽（2）X插槽通信托架电源管理软件捆绑软件套件CD环境工作温度50–104ºF（10–40ºC），45ºC，降额7.5%；最佳电池性能：77ºF（25ºC）存储温度32–77ºF；建议电池储存：59–77ºF（15–25ºC）相对湿度0–95%，1米（无噪音房间）时的非冷凝声音小于56 dBA，典型海拔9843英尺（3000米），无降额认证安全认证IEC 62040-1-1、IEC 60950、EN 62040-1-1和UL 1778 EMC符合EN 50091-2 A级质量ISO 9001:2000和ISO 14001:1996标记UL、cUL 1。由于产品的不断改进，程序规范可能会发生更改，恕不另行通知。四按钮图形LCD，带背光X插槽通信间隔#1风扇信号输入1信号输入2 REPO（常开）REPO（常闭）X插槽通信托架#2 DB-9通信端口继电器触点滑出式托盘上的内部电池（现场可更换）带盖的三个高模块的前视图12伊顿公司20和30 kVA1额定功率的技术规范200.9功率因数拓扑下的kVA/18 kW和30 kVA/27 kW
.<1 ms response time Efficiency 91%, typical Heat dissipation (BTU/hr) 10 kVA models: 3,798 @ 208V and 220V input 6,294 @ 480V and 600V (with input isolation transformer) 15 kVA models: 5,122 @ 208V and 220V input 8,134 @ 480V and 600V (with input isolation transformer) Battery Battery type 9 Ah, sealed, lead-acid, maintenance-free Battery runtime See battery backup time chart Battery replacement Field-replaceable Charger Default is 3.4A per battery string. Charger current is configurable from 0.5A to 25A per string with an overall maximum of 34A (limited by input current) Start-on-battery Allows start of UPS without utility input General Diagnostics Full system self-test at startup UPS bypass Automatic on overload or UPS failure Parallel for redundancy Yes, using Powerware Hot Sync technology and capacity Dimensions and weights See model selection table Overload (normal operation) 150% for 5 sec / 125% for 1 min (online), 110% for 10 min Communications LCD display Graphical LCD with blue backlight LEDs (4) LEDs for notice and alarm Audible alarms Yes Communication ports (1) RS-232, (1) relay contact, (1) REPO, (2) environmental input Communication slots (2) X-Slot communication bays Power management software Bundled Software Suite CD Environmental Operating temperature 50–104ºF (10–40ºC), 45ºC with 7.5% derating; Optimal battery performance: 77ºF (25ºC) Storage temperature 32–77ºF (0–25ºC); Recommended battery storage: 59–77ºF (15–25ºC) Relative humidity 0–95%, non-condensing Audible noise < 56 dBA at 1 meter (noiseless room) typical Altitude 9,843 ft. (3000m) without derating Certifications Safety certifications IEC 62040-1-1, IEC 60950, EN 62040-1-1, UL 1778 EMC compliance EN 50091-2 Class A Quality ISO 9001: 2000 and ISO 14001:1996 Markings UL, cUL 1. Due to continuous product improvements, program specifications are subject to change without notice. Four button graphical LCD with backlight X-Slot communication bay #1 Fans Signal input 1 Signal input 2 REPO (normally open) REPO (normally closed) X-Slot communication bay #2 DB-9 communication port Relay contact Internal batteries on slide out trays (fieldreplaceable) Front view of three-high module with cover off 12 EATON CORPORATION Technical Specifications for 20 and 30 kVA1 Power Ratings 20 kVA/18 kW and 30 kVA/27 kW at 0.9 power factor Topology
