PP826 3BSM011063-2工控模块机器人备件
注意：化学品的组合可能会产生不可预测的影响。在这种情况下，建议进行测试。若需要测试，供应商可提供小块乙烯基材料。5.3.2打滑/绊倒危险在大多数情况下，两种传感器垫模式都提供了防滑表面，但应保持无大量油脂、肥皂或凝胶沉积物。如果直肋侧位于最上方，建议肋骨穿过危险区域，以提高抓地力。5.3.3磨损和损坏垫子外表面可能因尖锐或重物的冲击而损坏。每次此类事件后，应检查垫子是否变形或穿孔，必要时应更换。垫子经过设计和测试，可以在任何一个地方承受一百万次操作。在使用中，不应超过任何单个位置的操作数。偶尔的重载（如3吨以下的卡车）不太可能损坏垫子，但不应在通过路线的交通中使用。5.3.4爆炸性环境该系统不适用于爆炸性环境。15 5.3.5 E.M.C.垫子系统符合欧洲EMC指令的要求。确保了在工业环境中可能出现的干扰条件下的正常操作，并已通过测试和认证。注：当存在异常高水平的电磁干扰时，可能需要采取特殊措施，例如靠近焊接或感应加热设备或靠近无线电发射机/收发器。5.3.6地板传感器垫的地板或安装表面必须平整、光滑且坚硬，即在预计的最大载荷下不会出现明显变形。起伏、凸起、大间隙或其他不规则现象将增加传感器垫的灵敏度，并可能导致间歇性意外关闭（有害跳闸）。
NOTE: Combinations of chemicals can have unpredictable effects. Testing is recommended in such cases. Small pieces of the vinyl material are available from supplier if testing is required. 5.3.2 SLIPPING / TRIPPING HAZARDS Both sensor mat patterns provide a non-slip surface under most conditions but should be kept free from large deposits of grease, soaps or gels. If the straight rib side is uppermost, it is recommended that the ribs run across the hazard to give improved grip. 5.3.3 WEAR AND DAMAGE The mat outer surface can be damaged by impacts from sharp or heavy objects. After every such event the mat should be inspected for deformation or puncturing and replaced if necessary. Mats have been designed and tested to withstand one million operations in any one spot. In use, this number of operations in any single location should not be exceeded. Occasional heavy loads, (e.g. up to 3 tonne trucks) are unlikely to damage the mats but they should not be used on traffic through routes. 5.3.4 EXPLOSIVE ATMOSPHERES The system is not suitable for use in explosive atmospheres. 15 5.3.5 E.M.C. The mat system complies with the requirements of the European EMC Directive. Normal operation under interference conditions likely in industrial environments is assured and has been tested and certified. NOTE: Special measures may be required in the presence of abnormally high levels of E.M.I. e.g. near to welding or induction heating equipment or near radio transmitters/transceivers. 5.3.6 FLOOR The floor or mounting surface for the sensor mats must be flat, smooth and rigid, i.e. show no perceptible distortion under the heaviest load anticipated. Undulations, protrusions, large gaps or other irregularities will increase the sensitivity of the sensor mats and may result in intermittent unintended switching off (nuisance tripping).
