PP875 3BSE092977R1机器人模块卡件.
最小弯曲半径[mm(in.)]0.68(0.027)12.7(0.50)1.16(0.046)12.7(0.50)1.6(0.063)15.8(0.625)2.28(0.090)15.8。5.玻璃纤维光缆尖端不能弯曲。只能按照《选择指南》中的规定弯曲特殊塑料光纤电缆传感端头。当使用可弯曲端头时,弯曲距离电缆传感端的距离不得超过19 mm(0.75 in.)。6.一些应用要求使用玻璃纤维光缆将传感器与高压隔离。必须为这些应用订购带有特殊非导电组件的定制电缆。7.X射线或伽马射线会导致玻璃纤维最终变得不透明。必须订购由特殊石英光纤构成的定制电缆,以便在高辐射区域使用。8.如有可能,在水下应用中使用透射光束传感。螺旋缠绕不锈钢护套通常不适用于潮湿应用。这些应用应使用带PVC护套的光纤电缆。9.具有分叉电缆的玻璃纤维光学传感器可以根据到目标的距离和传感器上的灵敏度调节来提供回射或漫射感测。如果传感器和电缆用于逆向反射传感,则必须将传感器的灵敏度调整得足够低,以避免来自待传感目标的不希望的漫反射响应。10.玻璃纤维光缆具有广阔的视野,通常为82_。通过将增程透镜组件连接到光纤的传感端,可以获得更小的视野。这些透镜组件还将增加可用的感测距离。有关更多信息,请参阅附件部分。
Minimum Bend Radius [mm (in.)] 0.68 (0.027) 12.7 (0.50) 1.16 (0.046) 12.7 (0.50) 1.6 (0.063) 15.8 (0.625) 2.28 (0.090) 15.8 (0.625) 3.17 (0.125) 19.0 (0.75) 3.96 (0.156) 25.4 (1.0) 4.57 (0.180) 31.7 (1.25) 4. Glass fiber optic cables cannot be cut, spliced or repaired. 5. Glass fiber optic cables tip cannot be bent. Only special plastic fiber optic cable sensing end tips can be bent as specified in the Selection Guide. When using bendable end tips, bend should not be attempted closer than 19 mm (0.75 in.) to the sensing end of the cable. 6. Some applications call for glass fiber optic cables to be used to isolate the sensor from high voltage. Custom cables with special nonconductive components must be ordered for these applications. 7. X-RAY or GAMMA radiation will cause glass fibers to eventually become opaque. Custom cables constructed with special optical quartz fibers must be ordered for use in areas with high radiation. 8. Use Transmitted Beam sensing in submerged applications when possible. Spiral-wound stainless steel sheathing is generally not suitable for wet applications. Fiber optic cables with PVC sheathing should be used for these applications. 9. A glass fiber optic sensor with a bifurcated cable can provide retroreflective or diffuse sensing depending upon the distance to the target and the sensitivity adjustment on the sensor. If the sensor and cable are to be used for retroreflective sensing, the sensitivity of the sensor must be adjusted low enough to avoid unwanted diffuse response from the targets to be sensed. 10. Glass fiber optic cables have a wide field of view, typically 82_. A smaller field of view can be achieved by attaching an Extended Range Lens Assembly to the sensing end of the fiber. These lens assemblies will also increase the available sensing distance. Refer to the Accessories section for more information.