PP885 3BSE069276R1控制器模块
222-COMM-B在24V DC时为75 mA 22-COMM-C在24V DC下为110 mA 22-COMM-D在24V DC 22-COMM-E下为60 mA在24V DC 22COMM-L下为140 mA在24V直流电时为60 mA 22-COMM-P在24V DC上为60 mA尺寸宽度高度深度108 mm（4.25 in.）108 mm（3.25 in.），端子连接器连接75 mm（2.95 in.）。)重量340克（12盎司）温度操作储存-10…50°C（14…122°F）-40…85°C（-40…185°F）相对湿度5…95%非冷凝大气重要：通信套件不得安装在环境大气中含有挥发性或腐蚀性气体、蒸汽或灰尘的区域。如果通信套件在一段时间内不会安装，则必须将其存放在不会暴露于腐蚀性环境的区域。震动操作非操作性30g，11 ms（DIN导轨安装）50g，11毫秒（面板安装）30g，11ms（DIN轨道安装）50g，11 ms，振动操作非操作型2.5g，5…2000 Hz 5.0g，5..2000 Hz UL UL508C cUL CAN/CSA C22.2 No.14-M91 CE EN50178和EN61800-3 CTick EN61800-3 20-XCOMM-AC-PS1是一个用于外部通信套件的附件交流至直流转换器。当控制面板内只有100…240V交流电源时使用。带有可互换插头的转换器如下所示。转换器连接到控制面板内的交流插座。使用适合您所在地区的插头：交流电源适配器规格电气连接为单个通信套件供电直流输出插头连接到22-XCOMM-DC-BASE上的配套直流ADP连接器。为菊花链通信套件供电其他通信套件可以通过菊花链连接在一起来供电。对于链中的每个通信套件，将所有DC“+”端子连接在一起，将所有直流“-”端子连接到一起（图5）。图5通过菊花链为多个通信套件供电可以菊花链连接在一起的通信套件的数量取决于：•菊花链连接的所有通信适配器所消耗的总电流。
2-COMM-B 75 mA at 24V DC 22-COMM-C 110 mA at 24V DC 22-COMM-D 60 mA at 24V DC 22-COMM-E 140 mA at 24V DC 22-COMM-L 60 mA at 24V DC 22-COMM-P 60 mA at 24V DC Dimensions Width Height Depth 108 mm (4.25 in.) 108 mm (4.25 in.) with terminal connector attached 75 mm (2.95 in.) Weight 340 g (12 oz.) Temperature Operating Storage -10…50°C (14…122°F) -40…85°C (-40…185°F) Relative Humidity 5…95% non-condensing Atmosphere Important: The Comms Kit must not be installed in an area where the ambient atmosphere contains volatile or corrosive gas, vapors or dust. If the Comms Kit is not going to be installed for a period of time, it must be stored in an area where it will not be exposed to a corrosive atmosphere. Shock Operational Non-operational 30g, 11 ms (DIN Rail Mount) 50g, 11 ms (Panel Mount) 30g, 11 ms (DIN Rail Mount) 50g, 11 ms (Panel Mount) Vibration Operational Non-operational 2.5g, 5…2000 Hz 5.0g, 5…2000 Hz UL UL508C cUL CAN / CSA C22.2 No. 14-M91 CE EN50178 and EN61800-3 CTick EN61800-3 The 20-XCOMM-AC-PS1 is an accessory AC-to-DC converter for use with the External Comms Kits. It is used when only 100…240V AC power is available inside a control panel. The converter, which comes with interchangeable plugs, is shown below. The converter connects to an AC receptacle inside the control panel. Use the appropriate plug for your region: AC Power Adapter Specifications Electrical Connections Powering a Single Comms Kit The DC output plug is connected to the mating DC ADP connector on the 22-XCOMM-DC-BASE. Powering Daisy-Chained Comms Kits Additional Comms Kits can be powered by daisy-chaining them together. For each Comms Kit in the chain, connect all DC “+” terminals together and all DC “-” terminals together (Figure 5). Figure 5 Powering Multiple Comms Kits via Daisy Chaining The number of Comms Kits that can be daisy-chained together is dependent on: • Total current consumed by all of the communication adapters being daisy-chained.
