PP886R 3BSE092985R1工控模块机器人备件
1.在将通信适配器安装到通信套件之前，确保将适配器的所有开关和跳线（如果适用）配置为适当的设置。有关详细信息，请参阅通信适配器用户手册。2.松开两个螺钉，从基座上拆下通信套件外壳盖。3.使用适配器的固定螺钉（适配器也接地）和通信套件（图1）提供的三个螺钉将通信适配器固定到机柜盖中。4.通信适配器配有15.24厘米（6英寸）长的内部接口（带状）电缆。将此电缆的一端插入通信套件机柜底部电源板上的配合连接器。图1安装和连接适配器5.将内部接口电缆的另一端插入通信适配器上的配合连接器。6.使用机箱盖中的两个螺钉将机箱盖固定到基座上。在将适配器连接到网络和驱动器之前，安装外部通信套件面板或DIN导轨安装通信套件。最小间距外部通信套件可以零堆叠（并排安装）。外壳底部留出75 mm（2.95 in.）的空间用于电缆引入。留出至少75 mm（2.95 in.）的外壳间隙深度，以容纳通信套件。外部通信套件（22-XCOMM-DC-BASE）•22-COMM-C ControlNet•22-COMM-L LonWorks（1）（1）此适配器将在DSI外部通信套件中运行，但与PowerFlex 4M驱动器不兼容。•22-COMM-D DeviceNet•22-COMM-P Profibus（2）（2）22-COMM-P具有不同的配置要求。有关详细信息，请参阅22-COMM-P用户手册（出版物22COMM-UM005）。•22-COMM-E以太网/IP•22-COMM-B BACnet MS/TP！
. Before you install the communication adapter into the Comms Kit, make sure to configure all of the adapter’s switches and jumpers, if applicable, to appropriate settings. Refer to the Communication Adapter User Manual for details. 2. Remove the Comms Kit enclosure cover from the base by unfastening its two screws. 3. Fasten the communication adapter into the enclosure cover by using the adapter’s captive screw, which also grounds the adapter, and the three screws provided with the Comms Kit (Figure 1). 4. The communication adapter is supplied with a 15.24 cm (6 in.) long Internal Interface (ribbon) cable. Plug one end of this cable into the mating connector on the power supply board in the base of the Comms Kit enclosure. Figure 1 Mounting and Connecting the Adapter 5. Plug the other end of the Internal Interface cable into the mating connector on the communication adapter. 6. Fasten the enclosure cover onto the base using the two screws in the cover. Mounting the External Comms Kit Panel or DIN rail mount the Comms Kit before connecting the adapter to the network and drive. Minimum Spacing External Comms Kits can be zero-stacked (side-by-side mounting). Allow 75 mm (2.95 in.) of space on the bottom of the enclosure for cable entry. Allow at least 75 mm (2.95 in.) of enclosure clearance depth to accommodate the Comms Kit. External Comms Kit (22-XCOMM-DC-BASE) • 22-COMM-C ControlNet • 22-COMM-L LonWorks (1) (1) This adapter will operate in the DSI External Comms Kit, but is not compatible with a PowerFlex 4M drive. • 22-COMM-D DeviceNet • 22-COMM-P Profibus (2) (2) The 22-COMM-P has different configuration requirements. See the 22-COMM-P User Manual (publication 22COMM-UM005) for details. • 22-COMM-E EtherNet/IP • 22-COMM-B BACnet MS/TP !
