PPC907VE 3BHE006373R0101处理器模块
27 440F-C4000D（按照步骤1-12正确安装）1.使用110V或230VAC电源时，将电压选择器切换至110V或230V（视情况而定）。注：系统从工厂发货时，选择器设置为230V AC 2。如果使用110V或230V AC电源，则应将其连接至所示端子，包括保护接地。检查电压选择开关的设置，参见步骤1。不要与步骤3所示的端子进行任何连接。保护接地线的尺寸应至少与电源线的尺寸相同。3.如果使用24VAC/DC电源，应将其连接至所示端子，确保极性正确。不要与步骤2所示的端子进行任何连接。对于24VAC，电源的接地极应连接到-ve端子。4.垫子连接：将垫子的引线连接到所示的端子。1=白色，2=白色，3=黑色，4=黑色。440F-C28013-八个标有1至8的快速连接适配器位于装置底座上，并提供与垫子的连接。31 A1•+重置IND 1 2 MC Y1 Y3 Y5••13 23 31 L N 110/230V AC电源A2-重置IND 3 4 MC Y2 Y4 Y6••14 24 32 110/230V VAC可选24V AC/DC 24V AC/DC电源接触器控制电源辅助可选远程指示装置电源绿色自动重置模式绿色手动重置模式绿色机器启用绿色白色黑色白色Y1Y2 Y4Y5Y6保险丝更换向上110V电源向下230V电源500 mAT自动1手动2 3 4 5 11 8 9 67 10模式设置电压设置手动自动日期110v 230V 24v勾选框将垫子连接到440F-C28013控制单元图27a终止未使用的垫子连接和连接垫子如果要连接到控制单元的垫子少于8个，则必须使用提供的短路插头终止其他连接。
27 440F-C4000D (correctly installed according to steps 1-12) 1. When using 110V or 230VAC power supply, switch the voltage selector to 110V or 230V (as appropriate). Note: When the system is shipped from the factory, the selector is set to 230V AC 2. If 110V or 230V AC power supply is used, it shall be connected to the terminals shown, including protective grounding. Check the setting of the voltage selector switch, see step 1. Do not make any connections to the terminals shown in step 3. The size of protective earth wire shall be at least the same as that of power wire. 3. If 24VAC/DC power supply is used, it should be connected to the terminals shown to ensure correct polarity. Do not make any connections to the terminals shown in step 2. For 24VAC, the ground electrode of the power supply should be connected to the - ve terminal. 4. Cushion connection: Connect the lead of the mat to the terminal shown. 1=white, 2=white, 3=black, 4=black. 440F-C28013 - Eight quick connect adapters marked 1 to 8 are located on the unit base and provide connections to the pads. 31 A1 •+RESET IND 1 2 MC Y1 Y3 Y5 • • 13 23 L N 110/230V AC POWER A2 - RESET IND 3 4 MC Y2 Y4 • • 14 24 32 110/230V VAC OPTIONAL 24V AC/DC POWER CONTACTOR CONTROL POWER SUPPLY AUXILIARY OPTIONAL REMOTE INDICATOR POWER SUPPLY GREEN AUTOMATIC RESET MODE GREEN MANUAL RESET MODE GREEN MACHINE ENABLE GREEN WHITE BLACK WHITE Y1Y2 FUSE REPLACEMENT UP 110V POWER SUPPLY DOWN 230V POWER SUPPLY 500 mAT AUTOMATIC 1 MANUAL 2 3 4 5 11 8 9 67 10 Mode setting Voltage setting Manual automatic date 110v 230V 24V check box Connect the mat to 440F-C28013 control unit Figure 27a Terminate unused mat connection and connecting mat If there are less than 8 mats to be connected to the control unit, you must use the provided short-circuit plug to terminate other connections.
