PPD103B03 DCS工控模块备件
图25进入电缆槽（周边饰板底部）的垫线建议切口的饰板固定件详图440F-T3013挠性导管入口建议切口的铝制内角周边饰板（与440F-T3510、440F-T3310和440F-T3210一起使用）440F-T3012铝制外角周边饰条（与440F-13510、440 F-T3310及440F-T3211一起使用）应力释放夹具挠性导管切口槽此处，在锋利的边缘上使用边缘护环剥下8mm的电线并插入压接筒。使用压接工具上正确的空腔尺寸压接。使用带导流板的加热枪加热压接接头，直到管道收缩，粘合剂收缩并流动。27 440F-T3210、440F-T3310和440F-T3510 440F-T3211和440F-T3411对于外部拐角装饰件，使用440F-T3014。对于内部拐角装饰件使用440F-T3105，440F-T3310和440F-T3510使用带挠性导管的应力消除夹具MAT 1 MAT 2 MAT 1 MAT 2 MAT3 MAT 1 MAT 2 45°45°MAT 3 MAT 4将所有装饰件切割成45°，如图所示。标记地板上的边缘装饰件固定位置，使装饰件与垫重叠。以装饰件上的孔为导向，标记并钻孔地板（如果需要，安装塞子）。清洁地板，并使用沉头螺钉将垫子和边缘装饰件固定到位，以适应应用。安装周边装饰件时，确保装饰件和地板之间或顶部和底部之间（取决于装饰件类型）没有任何电线被夹住或压碎。如果电线可能被夹住或拉动，应在电线离开周边装饰的地方使用应变消除夹。
Figure 25 Detail of trim panel fastener with recommended notch for pad wire entering cable tray (bottom of peripheral trim panel) 440F-T3013 Aluminum inner corner peripheral trim panel with recommended notch for flexible conduit entrance (used with 440F-T3510, 440F-T3310 and 440F-T3210) 440F-T3012 Aluminum outer corner peripheral trim strip (used with 440F-13510, 440 F-T3310 and 440F-T3211) Stress release fixture Flexible conduit notch here, Peel off 8mm wires on sharp edges with edge protectors and insert the crimping cartridge. Crimp with the correct cavity size on the crimping tool. Use a heat gun with a deflector to heat the crimp joint until the pipe shrinks and the adhesive shrinks and flows. 27 440F-T3210, 440F-T3310 and 440F-T3510 440F-T3211 and 440F-T3411 For exterior corner trim, use 440F-T3014. For the interior corner trim, use 440F-T3105440F-T3310 and 440F-T3510 to cut all the trims to 45 ° using the stress relief fixture MAT 1 MAT 2 MAT 1 MAT 2 MAT3 MAT 1 MAT 2 45 ° 45 ° MAT 3 MAT 4 with flexible conduit, as shown in the figure. Mark the fixing position of the edge trim on the floor so that the trim overlaps the pad. Using the holes in the trim as a guide, mark and drill the floor (install plugs if necessary). Clean the floor and fix the mat and edge trim in place with countersunk screws to suit the application. When installing the perimeter trim, ensure that no wires are trapped or crushed between the trim and the floor or between the top and bottom (depending on the trim type). If the wire may be pinched or pulled, strain relief clips should be used where the wire leaves the perimeter trim.
