IS200TPROH1BBB系统模块卡件
（4） 额定速度等级仅用于比较目的。使用运动分析仪为您的应用确定电机尺寸和/或Kinetix 5500驱动系统设计指南KNX-RM009出版物和Kinetix 5700驱动系统设计手册KNX-RM010出版物中的扭矩/速度曲线。在安装电机之前，执行这些检查步骤，并检查轴封、气压套件、联轴器和滑轮以及电气噪音防护指南。1.小心地从运输容器中取出电机。有关更多信息，请参阅第3页的起吊说明。2.目视检查电机有无损坏。3.检查电机框架、前输出轴和安装导向器是否有任何缺陷。4.立即通知承运人运输损坏。VP H-x xxx x x-x J x x D xx电机电缆长度01=1 m（3.2 ft）连续挠性额定值03=3 m（9.8 ft）连续柔性额定值05=5 m（16.4 ft）连续弹性额定值07=7 m（22.9 ft）连续刚性额定值09=9 m（29.5 ft）标准，非挠性额定值12=12 m（39.4 ft）标准、非挠性额定15=15 m（49.2 ft）标准和非挠性额定IEC公制，带螺纹的安装孔：D=标准单电缆制动器2=无制动器4=24V DC制动器轴键J=轴键连接器（1）1=单SpeedTec DIN连接器0=飞线反馈C=18位绝对单圈数字编码器（Hiperface DSL协议）Q=23位绝对多圈数字编码器，12位二级安全信道（2）W=18位绝对多匝数字编码器（Hiperface DSL协议）SIL 2（PLd）额定值，9位二级安全通道（3）额定转速（4）C=2300 rpm F=4500…6600 rpm D=3000 rpm M=6700 rpm E=3300…3900 rpm T=7200…8000 rpm磁体堆叠长度（1、2、3、4个堆叠）（5）框架尺寸-螺栓圆直径（BCD）063=63 mm 115=115 mm 075=75 mm 130=130 mm 100=100 mm 165=165 mm电压等级A=200V B=400V系列H=卫生(4) Rated speed hierarchy is only for comparative purposes. Use Motion Analyzer to size and select motors for your application, and/or the torque/speed curves in the Kinetix 5500 Drive Systems Design Guide, publication KNX-RM009, and the Kinetix 5700 Drive Systems Design Guide, publication KNX-RM010. (5) Refer to Motor Dimensionson page 9for dimensional changes that result from the number of magnet stacks. Before You Install the Motor Perform these inspection steps and review the guidelines for shaft seals, air-pressure kits, couplings and pulleys, and electrical noise prevention. 1. Remove the motor carefully from its shipping container. See Lifting Instructions on page 3 for more information. 2. Visually inspect the motor for any damage. 3. Examine the motor frame, front output shaft, and mounting pilot for any defects. 4. Notify the carrier of shipping damage immediately. VP H - x xxx x x - x J x x D xx On Motor Cable Length 01 = 1 m (3.2 ft) continuous-flex rated 03 = 3 m (9.8 ft) continuous-flex rated 05 = 5 m (16.4 ft) continuous-flex rated 07 = 7 m (22.9 ft) continuous-flex rated 09 = 9 m (29.5 ft) standard, non-flex rated 12 = 12 m (39.4 ft) standard, non-flex rated 15 = 15 m (49.2 ft) standard, non-flex rated IEC Metric, tapped mounting hole with: D = Standard single cable Brake 2 = No Brake 4 = 24V DC Brake Shaft Key J = Shaft key Connector (1) 1 = Single SpeedTec DIN connector 0 = Flying leads Feedback C = 18-bit absolute single-turn digital encoder (Hiperface DSL protocol) Q = 23-bit absolute multi-turn digital encoder (Hiperface DSL protocol) SIL 2 (PLd) rated, 12-bit secondary safety channel (2) W = 18-bit absolute multi-turn digital encoder (Hiperface DSL protocol) SIL 2 (PLd) rated, 9-bit secondary safety channel (3) Rated Speed (4) C = 2300 rpm F = 4500…6600 rpm D = 3000 rpm M= 6700 rpm E = 3300…3900 rpm T = 7200…8000 rpm Magnet Stack Length (1, 2, 3, 4 stacks) (5) Frame Size - Bolt Circle Diameter (BCD) 063 = 63 mm 115 = 115 mm 075 = 75 mm 130 = 130 mm 100 = 100 mm 165 = 165 mm Voltage Class A = 200V B = 400V Series Type H = Hygienic
