AO810 3BSE008522R1工控模块系统备件
在使用寿命结束时，该设备应与未分类的城市垃圾分开收集。安装说明45MLA测量光阵列传感器重要事项：保存这些说明以备将来使用。说明Allen-Bradley 45MLA测量光阵列是一种利用透射光束光电传感器对阵列来检测和测量物体的测量传感器。阵列外壳非常紧凑，允许在各种应用中轻松安装。45MLA封装为发射波束对，发射器和接收器阵列都包括在内。该系统需要Allen-Bradley 45MLA控制器，必须单独订购。控制器驱动发射器中的光电元件并读出接收器光束信息。使用这些外部控制器中的一个可以灵活地：•输出模拟信号（4…20 mA或0…10V）•使用独立的输出配置多达四个单独的传感区域，或•通过串行协议通信单个光束状态。此外，45MLA还可定制用于特定应用的悬垂和超高检测。功能•高度测量能力•薄型阵列（16 x 2•波束间距（间距）为10 mm（0.4 in.）或25 mm（1.2 in.）•最小可探测物体为18 mm（0.7 in.）或33 mm（1.3 in.）•长工作范围-4 m（13 ft）•快速反应时间和测量速度•传感阵列高度为300…1200 mm（11.8…47.2 in.）。)•IP54•可通过控制器获得单个光束状态（仅限串行通信型号）•与Allen-Bradley防护罩外壳相同™ Micro 400这些设备仅用于对象识别，不能用于保护人类（访问保护）。注意：所有适用指令的环境认证cULus和CE标志工作环境IP54工作温度[C（F）]0…+55°（+32…+131°）存储温度[C…F）]–20…+70°（-4…+158°）振动10…55 Hz；振幅0.35 mm（0.01英寸）；满足或超过IEC 60068-2-6冲击加速度10 g，脉冲持续时间16 ms；10…55赫兹；振幅0.35 mm（0.01英寸）；符合或超过IEC 60068-2-29相对湿度15…95%光学传感模式透射光束对传感范围0…4 m（0…13 ft）视野3.2°光源940 nm光束间距（间距）10 mm（0.4 in.）或25 mm（1.2 in.）最小可探测物体高度18 mm（0.7 in.）或33 mm（0.3 in.）。)LED指示灯红色：状态绿色：对准机械外壳材料铝透镜材料聚碳酸酯盖材料聚碳酸酯连接类型8针DC微型（M12）内螺纹QD，500 mm（20 in。
At the end of the service life, the equipment shall be collected separately from the unclassified urban garbage. Installation Instructions 45MLA Measurement Optical Array Sensor Important: Save these instructions for future use. It shows that Allen Bradley 45MLA measuring optical array is a measuring sensor that uses the transmission beam photoelectric sensor array to detect and measure objects. The array enclosure is very compact, allowing easy installation in a variety of applications. 45MLA is packaged as a transmit beam pair, including transmitter and receiver arrays. This system requires Allen Bradley 45MLA controllers, which must be ordered separately. The controller drives the photoelectric element in the transmitter and reads the beam information of the receiver. Using one of these external controllers gives you the flexibility to: • output analog signals (4... 20 mA or 0... 10V) • configure up to four separate sensing areas using independent outputs, or • communicate a single beam status via serial protocols. In addition, 45MLA can be customized for drape and superelevation detection for specific applications. Function • Height measurement capability • Thin array (16 x 2 • Beam spacing (spacing) is 10 mm (0.4 in.) or 25 mm (1.2 in.) • Minimum detectable object is 18 mm (0.7 in.) or 33 mm (1.3 in.) • Long working range - 4 m (13 ft) • Fast response time and measurement speed • Sensor array height is 300... 1200 mm (11.8... 47.2 in.) • IP54 • Single beam status can be obtained through the controller (serial communication models only) • Same as Allen Bradley shield housing ™ Micro 400 These devices are only used for object recognition and cannot be used to protect humans (access protection). Note: environmental certification of all applicable directives cULus and CE mark working environment IP54 Working temperature [C (F)] 0...+55 ° (+32...+131 °) Storage temperature [C... F)] – 20...+70 ° (- 4...+158 °) Vibration 10... 55 Hz; Amplitude 0.35 mm (0.01 inch); Meet or exceed IEC 60068-2-6 impact acceleration of 10g and pulse duration of 16ms; 10... 55 Hz; Amplitude 0.35 mm (0.01 inch); Conform to or exceed IEC 60068-2-29, relative humidity 15... 95%, optical sensing mode, transmitted light beam, 3.2 ° light source, field of vision 0... 4 m (0... 13 ft), 940 nm beam spacing (spacing) 10 mm (0.4 in.) or 25 mm (1.2 in.), minimum detectable object height 18 mm (0.7 in.) or 33 mm (0.3 in.) LED indicator red: status green: align the mechanical housing material aluminum lens material polycarbonate cover material polycarbonate connection type 8-pin DC micro (M12) internal thread QD, 500 mm (20 in.
