ABB PP825A 3BSE042240R3 控制系统
根据表11，通过使用DIP开关1和2的组合，可以将发射器强度设置为全功率（默认设置）、75%的全强度功率、60%或15%。可以将基本控制器配置为忽略短光束中断，例如通过检测区域的小颗粒引起的中断。可通过打开DIP开关4（并循环电源）启用双扫描模式。在该模式下，每个光束都会被求值两次（而不是一次），并且只有在两次求值期间中断的光束才会被识别。这允许忽略短暂的光束中断。响应时间增加。当启用双扫描模式时，使用电位计1可以使检测的最小持续时间更长。此额外的时间延迟可以从0到3.3秒不等。表10-J2引脚列表引脚信号说明备注1 0V DC电源-2+24V DC电源-3接地-4未连接未连接-5输入2未使用-6输入1未使用DIP开关S1（3）=0远程示教DIP开关S2（3）=1 7输出2错误0V DC=错误8输出1灯阵列中断0V DC=中断24V DC=未中断输入2 PNP NPN PNP NPP D7 LED-电源D3 LED输出1 D4LED输出2 D6 LED输入2 D5 LED输入1 RJ45连接器发射器RJ45连接器接收器D2 LED输入1电位计2电位计1可拆卸弹簧加载连接器输入逻辑跳线S1 J2输出1输出2输入1输入2 n.c.接地。24 VDC 0 VDC表11-基本型号DIP开关设置功能DIP开关S1（0：关闭，1：打开，X：不相关）87654321默认设置0 0 0 0 00 0 0 0最大发射器功率（100%）0xxxxx00降低发射器功率（最大值的75%）0xxxxx01降低发射器功率，最大值的60%）0xxxxx10降低发射器功率输出逻辑光操作=24V（PNP L.O.）暗操作=0V（NPN D.O.）0xx0xxxx输出逻辑光运行=0V安装说明教示说明基本控制器提供教示操作期间未评估的空白区域的功能。
According to Table 11, transmitter strength can be set to full power (default setting), 75% full strength power, 60% or 15% by using the combination of DIP switches 1 and 2. The basic controller can be configured to ignore short beam interruptions, such as those caused by small particles in the detection area. The dual scan mode can be enabled by turning on DIP switch 4 (and cycling the power). In this mode, each beam is evaluated twice (not once), and only beams that are interrupted during the two evaluations are recognized. This allows ignoring brief beam interruptions. Response time increases. When dual scan mode is enabled, the minimum duration of detection can be longer by using potentiometer 1. This additional time delay can range from 0 to 3.3 seconds. Table 10-J2 Pin List Pin Signal Description Remarks 1 0V DC Power Supply - 2+24V DC Power Supply - 3 Grounding - 4 Not Connected and Not Connected - 5 Input 2 Not Used - 6 Input 1 Not Used DIP Switch S1 (3)=0 Remote Teach DIP Switch S2 (3) =1 7 output 2 error 0V DC=error 8 output 1 lamp array interrupt 0V DC=interrupt 24V DC=uninterruptible input 2 PNP NPN PNP NPP D7 LED power D3 LED output 1 D4LED output 2 D6 LED input 2 D5 LED input 1 RJ45 connector transmitter RJ45 connector receiver D2 LED input 1 potentiometer 2 potentiometer 1 detachable spring loaded connector input logic jumper S1 J2 output 1 output 2 input 1 input 2 input 2 n.c. ground. 24 VDC 0 VDC Table 11 Basic model DIP switch setting function DIP switch S1 (0: off, 1: open, X: irrelevant) 87654321 Default setting 0 0 0 00 0 0 0 Maximum transmitter power (100%) 0xxxxx00 Reduce transmitter power (75% of the maximum) 0xxxxx01 Reduce transmitter power, 60% of the maximum value) 0xxxxx10 reduce transmitter power output logic light operation=24V (PNP L.O.) dark operation=0V (NPN D.O.) 0xx0xxxxx output logic light operation=0V installation instruction instruction instruction instruction basic controller provides the function of blank area not evaluated during instruction operation.
