ABB CP800 DCS工控模块备件
CAN和RS-485控制器模型提供了通过使用串行接口上的指定命令来调整这些设置的灵活性。重置默认参数设置所有控制器都带有默认参数值，可通过I/O型号的示教过程和RS-485和can型号的串行命令更改这些默认参数值。所有型号的默认参数都可以通过以下步骤重置：1.关闭控制器电源。2.将DIP开关阵列S1上的开关8设置为on。3.打开控制器电源。4.将开关8设置为DIP开关阵列S1关闭。5.现在应恢复默认设置。功能描述-模拟模型图3-模拟模型模拟控制器模型提供与目标高度、宽度或位置成比例的4…20 mA或0…10V（电流或电压可通过DIP开关选择）输出。输出会自动缩放到连接阵列的长度，因此大多数应用程序不需要额外调整。需要定制输出比例的应用程序可使用“示教”按钮。引脚列表表6显示了主连接器J2上的引脚分配。表4-控制器主板状态指示器状态指示器描述颜色含义D1灯阵列正常关闭目标存在或灯阵列未对齐绿色目标不存在和灯阵列对齐绿色闪烁低裕度/光强度不足D2灯阵列状态关闭目标不存在红色目标存在红色闪烁系统D3输出1关闭输出1关闭绿色输出1激活D4输出2关闭输出2非激活绿色输出2激活D5输入1关闭输入1非激活绿色输入1激活D6输入2关闭输入2非激活绿输入2激活D7电源关闭电源关闭绿色电源打开表5-控制器主PCB电位计调整电位计描述方向限值电位计1（1）（1）电位计1未用于模拟控制器型号。允许过手检测（2）或扫描中断忽略时间（3）（2）I/O、RS-485和CAN控制器。
The CAN and RS-485 controller models provide the flexibility to adjust these settings by using specified commands on the serial interface. Reset default parameter settings All controllers have default parameter values, which can be changed through the teaching process of I/O models and the serial commands of RS-485 and can models. The default parameters of all models can be reset through the following steps: 1. Turn off the controller power. 2. Set switch 8 on DIP switch array S1 to on. 3. Turn on the controller power. 4. Set switch 8 to DIP switch array S1 off. 5. The default settings should now be restored. Function Description - Analog Model Figure 3 - Analog Model The analog controller model provides 4... 20 mA or 0... 10V (current or voltage can be selected through DIP switches) outputs proportional to the target height, width, or position. The output is automatically scaled to the length of the connected array, so most applications do not require additional adjustments. Applications that need to customize the output scale can use the Teach button. Table 6 of the pin list shows the pin assignments on the main connector J2. Table 4 - Controller Main Board Status Indicator Status Indicator Description Color Meaning D1 Light Array Normally Closed Target Exists or Light Array Misaligned Green Target Does Not Exist and Light Array Aligns Green Flashing Low Margin/Insufficient Light Intensity D2 Light Array Status Closed Target Does Not Exist Red Target Exists Red Flashing System D3 Output 1 Shutdown Output 1 Shutdown Green Output 1 Activate D4 Output 2 Shutdown Output 2 Inactive Green Output 2 Activate D5 Input 1 Shutdown Input 1 Inactive Active green input 1 active D6 input 2 closed input 2 inactive green input 2 active D7 power off power off green power on table 5 controller main PCB potentiometer adjustment potentiometer description direction limit potentiometer 1 (1) (1) potentiometer 1 is not used for analog controller models. Allow pass detection (2) or scan interrupt ignore time (3) (2) I/O, RS-485 and CAN controllers.
