3500/22M 138607-01工控模块备件
In 2 PNP NPN PNP D7 LED--Power NPN型号特定扩展PCB D3 LED Out 1 D4 LED Out 2 D6 LED In 2 D5 LED In 1 RJ45连接器发射器RJ45连接器接收器D2 LED D1 LED Gaps In 1 Out 1 Out 2 In 1 In 2 N.C.接地。24 V DC 0 V DC Pot 2 Pot 1可拆卸弹簧加载连接器输入逻辑跳线S1 J2 J14 PHOTOSwitcher光电传感器45MLA测量阵列和控制器请访问我们的网站：www.ab.com/catalogs。1-163首选可用性类别。编号以粗体打印。底座PCB上的接头J2具有以下所有控制器型号的引脚。引脚信号说明1 0V DC电源2+24V DC电源3接地4未连接未连接5…8型号特定功能（见下文）连接器J2（在基础PCB上）上的引脚5…8具有不同的功能，适用于每个控制器型号。下表显示了每个特定型号的引脚连接。I/O型号RS485和CAN型号引脚信号描述备注引脚信号描述注释5输入2触发并保持DIP开关S1（7）=0 5输入2触发器并保持特殊功能悬置后传感器DIP开关S2（7）=1 6输入1未使用6输入1不使用DIP开关S 1（7）=0 7输出2光中断0V=中断悬置前传感器DIP切换S1（7悬垂7出2灯阵列中断0 V DC=中断24 V DC=未中断8出1悬垂0 V DC＝悬垂24 V DC＝无悬垂或超出高度（特殊功能）扩展PCB具有特定于每个单独型号功能的连接。以下是每种型号的引脚连接。连接器标记在PCB上。I/O型号连接器J14 RS485型号连接器J16 CAN型号连接器J12和J13（RJ45）引脚信号0V DC+24V DC引脚2导线4引脚信号1输出3区域Z1中断区域Z1未中断1 0V DC 0V DC 1 CAN H 2输出4区域Z2中断区域Z2未中断2-Rx+2 CAN L 3输出5区域Z3中断区域Z3未中断3屏蔽屏蔽3 0V DC 4输出6区域Z4中断Z4区未中断4-Rx--4未连接5 B Tx+5未连接6 A Tx-6屏蔽7 0V DC 8 CAN V+PHOTOSwitcher光电传感器45MLA测量阵列和控制器1-164请访问我们 首选可用性类别。
In 2 PNP NPN PNP D7 LED Power NPN model specific expansion PCB D3 LED Out 1 D4 LED Out 2 D6 LED In 2 D5 LED In 1 RJ45 connector transmitter RJ45 connector receiver D2 LED D1 LED Gaps In 1 Out 1 Out 2 In 1 In 2 N.C. Ground. 24 V DC 0 V DC Pot 2 Pot 1 detachable spring loaded connector input logic jumper S1 J2 J14 PHOTOSwitcher photoelectric sensor 45MLA measurement array and controller Please visit our website: www.ab.com/catalogs. 1-163 Preferred availability category. The numbers are printed in bold. Connector J2 on the base PCB has pins for all of the following controller models. Pin signal description: 1 0V DC power supply 2+24V DC power supply 3 ground 4 not connected Not connected 5... 8 Pin 5... 8 on connector J2 (on the base PCB) with specific functions (see below) has different functions and is applicable to each controller model. The following table shows the pin connections for each specific model. I/O model RS485 and CAN model pin signal description Remarks Pin signal description Note 5 Input 2 triggers and holds DIP switch S1 (7)=0 5 Input 2 triggers and holds special functions Rear suspension sensor DIP switch S2 (7)=1 6 Input 1 Not used 6 Input 1 Not used DIP switch S 1 (7)=0 7 Output 2 Optical interrupt 0V=Interrupt Front suspension sensor DIP switch S1 (7 overhang 7 out 2 lamp array interrupt 0 V DC=interrupt 24 V DC=not interrupt 8 out 1 overhang 0 V DC=overhang 24 V DC=no overhang or over height (special function) The extended PCB has a connection specific to each individual model function. The following are the pin connections for each model. The connector is marked on the PCB. I/O model connector J14 RS485 model connector J16 CAN model connector J12 and J13 (RJ45) Pin signal 0V DC+24V DC Pin 2 Wire 4 Pin signal 1 Output 3 Area Z1 Interruption area Z1 Not interrupted 1 0V DC 0V DC 1 CAN H 2 Output 4 Area Z2 Interruption area Z2 Not interrupted 2-Rx+2 CAN L 3 Output 5 Area Z3 Interruption area Z3 Not interrupted 3 Shield shield 3 0V DC 4 Output 6 Area Z4 Interruption Z4 Area 4-Rx-4 Not connected 5 B Tx+5 Not connected 6 A Tx-6 Shield 7 0V DC 8 CAN V+PHOTOSwitcher Photoelectric Sensor 45MLA Measurement Array and Controller 1-164 Please visit us Preferred availability category.
