RF533 3BSE014227R1备件模块
3.传感器边缘的跳闸危险通过入口处的斜坡减少。斜坡还可以保护连接电缆。可选的周界修剪是渐变截面。4.电缆槽安装在固定防护装置的外部。这可防止其被误用为进入危险区域。5.复位按钮位于保护良好的位置，可完全看到机器。6.垫安装正确。5.7电气接口系统提供的保护取决于系统和机器之间的正确接口。系统的安全输出触点布置为两个独立的无电压N/O触点对。端子位置在第6.2节中给出，额定值在第4.1 2 6 4 5 1 3 20节中给出。根据EN 954-1，控制单元符合第3类。与其他安全垫和地板一样，传感器垫的第3类性能无法在严重机械损坏或长期退化导致的故障中实现。根据EN 954-1，传感器垫符合第1类。由互连传感器垫和控制单元组成的系统符合EN 954-1第3类的要求。垫系统可用作唯一的保护措施或与其他措施或装置（如安全光幕、工作系统）结合使用。如果协调的欧洲“C”标准适用于机器类型，它将包含机器安全相关控制系统的要求和指南。EN954-1也提供了指导。重要的是，应根据EN 954-1的适当类别提供针对可预见故障的充分保护，因此，建议在所有高风险应用中使用具有复制和监控最终开关元件（接触器）的双通道配置。图15、16、17和18给出了垫系统的互连示例。21图15显示了单接触器（单通道）、440F-4000P和440F-C4000S应用的示例连接图。电路状态-电源打开-传感器垫上不存在-复位按钮已操作（如果处于手动复位模式）-机器启动电路已启用。注意：如果接触器卡在ON位置，则当垫处于ON位置时，电机不会停止。图16显示了两个接触器和接触器监控（双通道）440F-4000P和440F-C4000S的应用连接图示例。电路状态-电源打开-传感器垫上不存在-复位按钮已操作（如果处于手动复位模式）-机器启动电路已启用。注意：如果任何一个接触器卡在ON（接通）位置，则当垫放在上面时，电机将停止，并检测到故障。M K1 K2 24VDC，电源L1 L2 L3辅助输出辅助输入K1（AUX）K2（au）启动瞬时按钮停止瞬时按钮熔断器电机保护，例如热断路器12 3 4+VE 31 13 23 MC MC 32 14 24控制单元K1 K2-VE正向引导接触器辅助触点L N110VAC，230VAC电源（备用电源连接）白色-白色-黑色-黑色传感器垫内部传感器垫板N/O PB R IND M K1 24VDC，电源L1 L2 L3辅助输出辅助输入K1（辅助）启动瞬时按钮停止瞬时按钮保险丝电机保护，例如。
3. Trip hazard at the edge of the sensor is reduced by the ramp at the entrance. The slope also protects the connecting cable. The optional perimeter trim is a gradient section. 4. The cable tray shall be installed outside the fixed protective device. This prevents it from being misused to enter hazardous areas. 5. The reset button is located in a well protected position, and the machine can be completely seen. 6. The gasket is installed correctly. 5.7 The protection provided by the electrical interface system depends on the correct interface between the system and the machine. The safe output contacts of the system are arranged as two independent voltage free N/O contact pairs. Terminal locations are given in Section 6.2 and ratings are given in Section 4.1 2 6 4 5 1 3 20. According to EN 954-1, the control unit complies with category 3. As with other safety pads and floors, the Class 3 performance of sensor pads cannot be achieved in the case of failures caused by severe mechanical damage or long-term degradation. According to EN 954-1, the sensor pads comply with category 1. The system consisting of interconnected sensor pads and control units complies with the requirements of EN 954-1, class 3. The cushion system can be used as the only protective measure or in combination with other measures or devices (such as safety light curtain and working system). If the harmonized European "C" standard applies to machine types, it will contain requirements and guidelines for machine safety related control systems. EN954-1 also provides guidance. It is important that adequate protection against foreseeable faults should be provided in accordance with the appropriate categories of EN 954-1, therefore it is recommended that a dual channel configuration with duplicated and monitored final switching elements (contactors) be used in all high-risk applications. Figures 15, 16, 17, and 18 show interconnection examples of the mat system. 21 Figure 15 shows an example connection diagram for single contactor (single channel), 440F-4000P and 440F-C4000S applications. Circuit status - power on - not present on sensor pad - reset button operated (if in manual reset mode) - machine start circuit enabled. Note: If the contactor is stuck in the ON position, the motor will not stop when the pad is in the ON position. Figure 16 shows the application connection diagram example of two contactors and contactor monitoring (dual channel) 440F-4000P and 440F-C4000S. Circuit status - power on - not present on sensor pad - reset button operated (if in manual reset mode) - machine start circuit enabled. Note: If any contactor is stuck in the ON position, the motor will stop and a fault will be detected when the pad is placed on it. M K1 K2 24VDC, power supply L1 L2 L3 auxiliary output auxiliary input K1 (AUX) K2 (au) start instantaneous button stop instantaneous button fuse motor protection, such as thermal circuit breaker 12 3 4+VE 31 13 23 MC MC 32 14 24 control unit K1 K2-VE forward guiding contactor auxiliary contact L N110VAC, 230VAC power supply (standby power connection) white white black sensor pad internal sensor pad N/O PB R IND M K1 24VDC, Power supply L1 L2 L3 auxiliary output auxiliary input K1 (auxiliary) start instantaneous button stop instantaneous button fuse motor protection, for example.
