RX881工控机器人备件
•所定义的周边和危险之间的整个地板区域必须由垫子传感器覆盖，以便在不启动垫子系统的情况下无法接近或接近危险。危险垫8用作防护周界内的存在感测系统图6用作防护周界中的存在感系统。该系统提供存在感测，以防止人员在封闭区域内时机器启动。•当系统以这种方式用作二级保护系统时，第5.4.1节中给出的安全距离计算不适用。周界防护方法应符合所有相关要求封闭周界和危险区域之间的整个地面区域必须由垫子传感器覆盖，以便人员在不启动垫子系统的情况下无法进入封闭区域。危险压力敏感垫固定防护联锁门（带锁）9第4节-规范控制单元440F-C4000P 440F-C400S 440F-C4000 D符合EN 1760-1、EN 60204-1、EN 954-1：3类，UL 508响应时间（垫子按压-35mS安全触点打开）环境保护IP65 NEMA12外壳-IP40 DIN0470端子-IP20 DIN0470脉冲耐受电压2500V污染等级III最小开关电流/电压10mA/10V电源-用户选择110/230V AC（50-60Hz）和24V AC/DC+10%-15%（110V设置也允许在100v±10%下使用）功耗<9 VA 6W继电器输出2个独立的无电压N/O安全触点1个无电压N/C辅助触点NB-Aux不得用于外部安全电路保险丝，AC最大5A（快速作用），AC最大2.5A（快速作用的），DC使用类别AC-15；4A/250V交流-直流-13；2A/30V DC输出：远程复位/指示灯24V DC/0.24W输入远程复位开关（2 x N/O）安全输入4线垫指示灯LED 1电源绿色LED 2自动复位模式绿色LED 3手动复位模式绿色LED4机器启用绿色内部控制交流电压选择器，自动/手动复位选择器内部电源保险丝500mA可更换500mA可替换500mA可换（2个）（2个关闭）（1个关闭）500mA可重置（1个）工作温度范围-10°C至+45°C湿度在+50°C时敢达90%RH根据IEC 68-2-6进行振动测试，频率范围10-55Hz，每轴位移0.15mm 10个周期，扫描速率，每分钟1倍频程MC-MC接触器监控回路常闭接触器回路最大导线尺寸为1 x 1.5mm2绞合1 x 1.5mmm2绞合2 x 1.5mm2，套管剥开，套管剥掉5mm，1 x 2.5mm2 5mm，1×2.5mm2 8mm，2 x 2.5mm2实心导体实心导体Ter端子负端子负端子正/负固定螺钉M2.5螺钉M2.5端子螺钉M3.5，安装在45°处，45°处安装，自提升至PCB至PCB连接，根据VDE 0110材料，可单独拆卸的垫圈端子板安装组C，聚碳酸酯钢，带聚碳酸酯聚碳酸酯屏幕固定细节4 x M4孔4 x M6孔35mm，导轨其他。在手动复位N/A N/A模式（M）下，
• The entire floor area between the defined perimeter and the hazard must be covered by a mat sensor so that the hazard cannot be approached or approached without activating the mat system. The hazard pad 8 is used as a presence sensing system within the protective perimeter Figure 6 is used as a presence sensing system within the protective perimeter. The system provides presence sensing to prevent the machine from starting when people are in an enclosed area. • When the system is used as a secondary protection system in this way, the safety distance calculation given in Section 5.4.1 is not applicable. The perimeter protection method shall comply with all relevant requirements. The entire ground area between the enclosed perimeter and the hazardous area must be covered by mat sensors so that personnel cannot enter the enclosed area without starting the mat subsystem. Dangerous pressure sensitive pad fixed protective interlocking door (with lock) 9 Section 4 - Specification Control unit 440F-C4000P 440F-C400S 440F-C4000 D according to EN 1760-1, EN 60204-1, EN 954-1:3, UL 508 response time (cushion pressing - 35mS safety contact opens) Environmental protection IP65 NEMA 12 housing - IP40 DIN0470 terminal - IP20 DIN0470 pulse withstand voltage 2500V Pollution level III Minimum switching current/voltage 10mA/10V power supply - user selects 110/230V AC (50-60Hz) and 24V AC/DC+10% - 15% (110V setting is also allowed to be used under 100v ± 10%) Power consumption<9 VA 6W relay outputs 2 independent voltage free N/O safety contacts 1 voltage free N/C auxiliary contact NB Aux shall not be used for external safety circuit fuses, AC maximum 5A (fast acting), AC maximum 2.5A (fast acting), DC use category AC-15; 4A/250V AC-DC-13; 2A/30V DC output: remote reset/indicator light 24V DC/0.24W input remote reset switch (2 x N/O) safety input 4 wire pad indicator light LED 1 power supply green LED 2 automatic reset mode green LED 3 manual reset mode green LED 4 machine enable green internal control AC voltage selector, Automatic/manual reset selector internal power fuse 500mA replaceable 500mA replaceable 500mA replaceable (2) (2 off) (1 off) 500mA resettable (1 off) Operating temperature range - 10 ° C to+45 ° C Humidity at+50 ° C dare to reach 90% RH Vibration test according to IEC 68-2-6, frequency range 10-55Hz, displacement of each shaft 0.15 mm 10 cycles, scanning rate, One octave per minute MC-MC contactor monitoring circuit Normally closed contactor circuit The maximum conductor size of the circuit is 1 x 1.5mm2 twisted 1 x 1.5mm2 twisted 2 x 1.5mm2, the casing is stripped, the casing is stripped 5mm, 1 x 2.5mm2 5mm, 1 × 2.5mm2 8mm, 2 x 2.5mm2 solid conductor Ter terminal negative terminal negative terminal positive/negative fixing screw M2.5 screw M2.5 terminal screw M3.5, installed at 45 °, installed at 45 °, self lifting to PCB to PCB connection, according to VDE 0110 material, separately removable gasket terminal board installation group C, polycarbonate steel, with polycarbonate polycarbonate screen fixing details 4 x M4 holes 4 x M6 holes 35mm, other rails. In the manual reset N/A N/A mode (M),
