UAZ325575 DCS工控模块备件
摩擦组件
单位滞后时间停止次数 摩擦组件摩擦组件设置摩擦组件杆摩擦组件滑动摩擦组件额定145摩擦组件转速参考扭矩控制链接[4B2]S曲线转速参考摩擦组件扭矩添加66自动化出版物PFLEXRM002DENE2013年8月第1章详细驱动配置和操作接地，概述详细信息，请参阅脉宽调制（PWM）交流驱动器的接线和接地指南，出版物DrivesIN001。HIM内存请参阅第33页的复制目录。HIM操作当模块键在预定时间内处于非活动状态时，将显示用户显示。显示器可编程显示相关信息。设置用户显示设置用户显示器的属性•可以根据需要设置以下HIM参数：•用户显示器启用或禁用用户显示器。•用户显示1选择显示在用户显示顶部行的用户显示参数。•用户显示2选择显示在用户显示底部的用户显示参数。
•用户显示时间设置
在HIM显示用户显示之前，触摸最后一个编程键后的秒数。步进键示例显示1.按向上箭头或向下箭头滚动至Operator Intrfc。按Enter键。2.按向上箭头或向下箭头滚动到用户显示。按Enter键。3.选择所需的用户显示。按Enter键。滚动到用户显示所基于的参数。4.按Enter键。设置比例因子。5.按Enter键保存比例因子并移至最后一行。6.按向上箭头或向下箭头更改文本。7.按Enter键保存新用户显示。选择操作员Intrfc：更改密码用户显示参数自动化出版物PFLEXRM002DENE2013年8月67详细驱动配置和操作第1章惯性自适应惯性自适应用于补偿齿轮箱和/或“弹性”联轴器存在时发生的运动损失。惯性自适应可允许用户将速度调节器带宽增加四倍。例如，显示了连接到齿轮箱的电机：该齿轮箱可以由弹簧（k）和齿轮后间隙（BL）表示：当电机速度增加时，齿轮箱的齿啮合之前有一段时间（由Dx表示）。
Friction components
Number of stops per unit lag time Friction assembly Friction assembly Setting Friction assembly Rod Friction assembly Sliding friction assembly Rated 145 Friction assembly Speed Reference Torque Control Link [4B2] S Curve Speed Reference Friction assembly Torque Add 66 Automation publication PFLEXRM002DENE August 2013 Chapter 1 Detailed Drive Configuration and Operation Grounding, General Details, See Wiring and Grounding Guidelines for Pulse Width Modulated (PWM) AC Drives, PublicationDrivesIN001. For HIM memory, refer to the copy directory on page 33. HIM Operation When the module key is inactive for a predetermined period of time, the user display will be displayed. The display can be programmed to display relevant information. Set User Display Set the properties of the user display • The following HIM parameters can be set as needed: • User display Enable or disable the user display. • User Display 1 Select the user display parameters displayed in the top line of the user display. • User Display 2 Select the user display parameters displayed at the bottom of the user display.
• User display time settings
The number of seconds after touching the last programming key before the HIM displays the user display. Step key example display 1. Press up arrow or down arrow to scroll to Operator Intrfc. Press Enter. 2. Press the up arrow or down arrow to scroll to the user display. Press Enter. 3. Select the desired user display. Press Enter. Scroll to the parameter on which the user display is based. 4. Press Enter. Sets the scale factor. 5. Press Enter to save the scale factor and move to the last line. 6. Press the up arrow or the down arrow to change the text. 7. Press Enter to save the new user display. Select Operator Intrfc: Change Password User Display Parameters Automation Publication PFLEXRM002DENE August 67, 2013 Detailed Drive Configuration and Operation Chapter 1 Inertial Adaptive Inertial Adaptive is used to compensate for loss of motion in the presence of the gearbox and/or "flexible" couplings. Inertial adaptation allows the user to quadruple the speed regulator bandwidth. For example, the motor connected to the gearbox is shown: the gearbox can be represented by the spring (k) and the backlash behind the gear (BL): when the motor speed increases, there is a period of time (represented by Dx) before the teeth of the gearbox mesh.
