UFC092BE01 HIEE300910R1工控模块系统备件
参数是驱动器到控制器的输出
用于读取参数。使用“数据输出”参数可读取总共8个参数。在700S中，每个参数都是32位整数或32位浮点（实数）。这意味着数据链路参数为32位。参数723[Dlink OutDataTyp]用于选择8个“数据输出”数据中的每一个是整数还是实数。要读取16位或32位整数参数，[Data Out x Int]参数之一必须链接到所需的整数参数。然后，[Dlink OutDataType]中[Data In x Int]参数对应的位设置为0。要读取实参数，[Data Out x real]参数之一必须链接到所需的实参数。然后[Dlink OutData Type]中[Data Out x Real]参数对应的位设置为1。示例配置3：使用Datalink读取整数参数•724[Data Out A1 Int]链接到741[Position Status]•723[Dlink OutDataType]位0设置为0[Data Out A1Int]到控制器的值包含[Position Status]的值。使用[Data Out A1 Int]，[Dlink OutDataType]位0设置为0，因为[Position Status]是整数参数。
示例配置：
使用Datalink读取实参数•[Data Out A1 Real]链接到[Output Current]•[Dlink OutDataType]位1设置为1。[Data Out Al Real]到控制器的值包含[Output Current]的值。[数据输出A1实]输出电流]。使用[Data Out A1 Real]，[Dlink OutDataType]位0设置为1，因为[Output Current]是一个实数参数。36自动化出版物PFLEXRM002DENE2013年8月第1章详细驱动器配置和操作减速时间参数33【减速时间】设置了在斜坡停止命令期间或在命令速度下降期间驱动器减速输出的速率。建立的速率是编程的减速时间和编程的电机额定转速参数4[motor NP RPM]的结果，如下所示：时间可在0.01至6553.5秒之间以0.0001秒的增量进行调整。
The parameter is the output from the driver to the controller
Used to read parameters. A total of 8 parameters can be read using the Data Output parameter. In 700S, each parameter is a 32-bit integer or 32-bit floating point (real number). This means that the data link parameter is 32 bits. Parameter 723 [Dlink OutDataType] is used to select whether each of the 8 "data output" data is an integer or a real number. To read 16 bit or 32-bit integer parameters, one of the [Data Out x Int] parameters must be linked to the desired integer parameter. Then, the bit corresponding to the [Data In x Int] parameter in [Dlink OutDataType] is set to 0. To read real parameters, one of the [Data Out x real] parameters must be linked to the desired real parameter. Then the bit corresponding to the [Data Out x Real] parameter in [Dlink OutData Type] is set to 1. Example configuration 3: Use Datalink to read integer parameters • 724 [Data Out A1 Int] to link to 741 [Position Status] • 723 [Dlink OutDataType] Bit 0 is set to 0 [Data Out A1Int] The value to the controller includes the value of [Position Status]. With [Data Out A1 Int], [Dlink OutDataType] bit 0 is set to 0, because [Position Status] is an integer parameter.
Example configuration:
Use Datalink to read real parameters • [Data Out A1 Real] link to [Output Current] • [Dlink OutDataType] bit 1 is set to 1. The value from [Data Out Al Real] to the controller includes the value of [Output Current]. [Data output A1 real] Output current]. With [Data Out A1 Real], [Dlink OutDataType] bit 0 is set to 1 because [Output Current] is a real parameter. 36 Automation publication PFLEXRM002DENE, August 2013, Chapter 1, Detailed Drive Configuration and Operation Deceleration Time parameter 33 [Deceleration Time] sets the speed at which the drive decelerates during a ramp stop command or during a command speed decrease. The established speed is the result of the programmed deceleration time and the programmed motor rated speed parameter 4 [motor NP RPM], as shown below: the time can be adjusted in 0.0001 second increments between 0.01 and 6553.5 seconds.
