UNS2881B-P,V1/3BHE009319R0001自动化模块备件
接线图索引输入智商传感器
类型交流输出源输出汇输出 电子电流：当输出处于“打开”或“断电”状态时流经输出的电流。所有固态传感器都会出现这种情况。这通常是线传感器的一个问题其中这两条线中的电流是向传感器的电子设备供电所必需的。在使用线交流或直流传感器的应用中传感器的泄漏电流可能足以使模块的输入通电传感器打开和关闭但模块始终保持“打开”。为了帮助模块响应传感器的两种状态可以与模块并联添加电阻器。该放气电阻器允许额外的电流路径从而减少输入输出模块的输入电流。的放气电阻器尺寸的排气电阻器尺寸的放气电阻器大小块的放气电阻尺寸的放气电阻大小。块的放气电阻器尺寸弯曲模块 输入泄漏电流强制兼容性 传感器泄漏电流泄放电阻器输入模块最大关断状态电流 交流电 交流交流 直流 交流电压交流电压交流电压交流电流交流传感器实际泄漏电流强制兼容性最大传感器泄漏电流放气电阻器输入模块最大关断状态电流
电假设为伏直流电伏直流直流直流电压 传感器传感器动作弯曲模块 输入泄漏电流强制兼容性最大传感器泄漏电流泄放电阻器输入模块最大关断状态 磁跳闸 中的额定电流。极数极 §不提供过电流保护可在 以上打开。中断额定值 编号分断容量赫兹 分断能力 中断 代码‡ 极串联 磁极串联 这些额定值尚未进行认证测试。第有关的信息请参阅下表。编号选择热磁固定热固定磁组装塑壳断路器框架塑壳开关§产品选择框架类别。编号公告塑壳断路器请访问我们的网站：出版物目录编号说明 公告编号代码描述全球塑壳断路器框架额定代码描述 固定中断额定值断开容量基于时的代码描述 和保护类型代码描述固定热固定磁调节热固定磁性塑壳开关隔离器极代码描述极电流范围代码描述例如= 例如= 工厂安装的内部选项♦ 分流跳闸和欠压释放装置代码说明分流跳闸 分流跳闸 直流分流跳闸 并联跳闸 分流跳闸 分流跳闸
WIRING DIAGRAM INDEX INPUT IQ SENSOR
Type AC output source output sink output electronic current: the current flowing through the output when the output is in the "open" or "power off" state. This occurs with all solid-state sensors. This is usually a problem with wire sensors where the current in these two wires is necessary to power the electronics of the sensor. In applications using in-line AC or DC sensors, the leakage current of the sensor may be sufficient to power the input of the module The sensor turns on and off but the module remains "on" at all times. To help the module respond to the two states of the sensor, a resistor can be added in parallel with the module. The bleed resistor allows additional current paths to reduce the input current to the I/O module. Outgassing resistor size outgassing resistor size outgassing resistor size block outgassing resistor size outgassing resistor size. Block outgassing resistor size 63
The electrical assumption is V DC V DC DC voltage sensor sensor action bending module input leakage current forced compatibility maximum sensor leakage current relief resistor input module maximum off state magnetic trip rated current. Pole number pole § can be opened above without providing overcurrent protection. Interruption rating number Breaking capacity Hertz Breaking capacity Interruption code ‡ Pole series pole series These ratings have not been certified. Refer to the following table for information on section. Select thermal magnetic fixed thermal fixed magnetic assembly molded case circuit breaker frame molded case switch § Product selection frame category. Numbering Bulletin Molded Case Circuit Breaker Please visit our website: Publications Catalogue Numbering Description Bulletin Number Code Description Global Molded Case Circuit Breaker Frame Rating Code Description Fixed Interruption Rating Time Based Code Description and Protection Type Code Description Fixed Thermal Fixed Magnetic Modulator Thermal Fixed Magnetic Molded Case Switch Isolator Pole Code Description Pole Current Range Code Description Example=Example=Factory Installed Internal Option ♦ Code description of shunt trip and undervoltage release device shunt trip shunt trip DC shunt trip shunt trip shunt trip shunt trip shunt trip
