VMIVME-4132-010系统备件
针板旨在与驱动器一起
使用但可用于具有最低要求的非应用。安装在驱动器上的转接板尺寸产品目录号和 这些转接板适用于需要… 转换器用于控制电源的应用中的驱动器产品目录编号 和。针板旨在与驱动器一起使用但可用于具有最低要求的非应用。驱动器安装的转接板尺寸产品目录号和 重要信息：由于连接接口电缆时的空间限制连接到 接口驱动器时需要。重要信息：当连接到 驱动器时请勿使用。Ö 尺寸单位为针连接器显示为无盖 针连接件显示为不带盖 Ö。针连接器显示为无盖 针接头显示为不带盖出版物年月发行说明 产品目录号固件版本的增强功能此版本固件中没有增强功能。纠正的异常这些纠正适用于固件版本更高版本：和编码器支持已纠正以在同一方向上移动数千圈后通过电源循环保持绝对位置。
数字伺服驱动器
有关先前的固件更正请参阅这些出版物：数字伺服驱动器 固件版本出版物 出版物年月 固件发行说明限制当 与 伺服模块和 驱动器一起使用时这些限制适用。不支持窗口注册。如果指令中启用了窗口注册则指令将无法完成。不支持摩擦扭矩补偿和齿隙补偿。调整手动调整屏幕的偏移选项卡中的值将无效。傅固件版本可能支持此参数因此设置应保持默认值%。不支持速度下降。调整自定义增益属性屏幕中的值不会产生任何影响。不支持在轴属性屏幕的驱动选项卡中访问的以下实时轴信息属性：使用双回路配置时轴属性对话框的电机反馈和辅助反馈选项卡上的分辨率单位设置转英寸毫米必须相同。在驱动参数的之后在设置位之后至少等待毫秒然后再对设置结果进行操
The needle plate is designed to work with the drive
Use but can be used for non applications with minimum requirements. The size of the docking stations installed on the drives Catalog numbers and these docking stations are applicable to the drive catalog numbers and in applications where... converters are used to control power. The needle plate is intended for use with drives but can be used for non applications with minimum requirements. Size of adapter plate installed on the drive Catalog number and important information: required when connecting to the interface drive due to space limitations when connecting the interface cable. Important: Do not use when connected to the drive. Ö The dimension unit is the pin connector, which is displayed as a pin connector without a cover, which is displayed as a pin connector without a cover. Pin connectors are displayed as uncovered pin connectors are displayed as uncovered publications Monthly Release Notes Catalog Number Firmware Version Enhancements There are no enhancements in this version of firmware. Corrected exceptions These corrections apply to later firmware versions: and encoder support have been corrected to move thousands of cycles in the same direction to maintain absolute position through power cycles.
Digital servo driver
Refer to these publications for previous firmware corrections: Digital Servo Drive Firmware Versions Publications Monthly Firmware Release Notes Limitations These restrictions apply when used with servo modules and drives. Window registration is not supported. If window registration is enabled in a directive, the directive cannot be completed. Friction torque compensation and backlash compensation are not supported. Adjust The values in the Offset tab of the Manual Adjustment screen will not be valid. The firmware version may support this parameter, so the setting should remain at the default value of%. Speed droop is not supported. Adjusting the values in the Custom Gain Attributes screen has no effect. The following real-time axis information properties accessed in the Drive tab of the Axis Properties screen are not supported: The resolution unit settings in inches and millimeters on the Motor Feedback and Auxiliary Feedback tabs of the Axis Properties dialog box must be the same when using a dual circuit configuration. Wait for at least milliseconds after setting the bit after driving the parameter, and then operate on the setting result. Position internal error acceleration.作。位置内部误差加速度。
