ZUBA003203R0001工控备件模块
更新适配器
注意：存在永久性设备损坏的风险。启动闪存更新后，在下载完成且适配器MOD状态指示灯开始闪烁绿色之前，请勿断开驱动器（或22-XCOMM-DC-BASE外部通信套件，如果使用）的电源。如果在此之前断电，适配器可能会永久损坏。以这种方式损坏的适配器无法修理。22-COMM-E EtherNet/IP适配器固件v1.008 5安装闪存套件1。请访问Allen Bradley适配器安装闪存套件。（这也会自动在您的计算机上安装ControlFLASH软件。）2.您现在可以使用DriveExplorer、DriveExecutive、ControlFLASH或HyperTerminal来更新适配器。请参阅下面的相应章节并按照说明进行操作。使用DriveExplorer Lite/Full to Flash Update 1。安装了Flash Kit（请参阅安装闪存套件）后，启动DriveExplorer并使用连接到适配器的驱动器联机（通过以太网连接或1203-USB或22-SCM-232转换器）。2.在DriveExplorer树视图中，单击22-COMM-E EtherNet/IP。
以显示适配器的Properties屏幕
在22-COMM-E属性屏幕上，单击详细信息选项卡。重要信息：此更新可能会导致适配器参数恢复为默认值。升级前，您可能需要使用DriveExplorer或HIM CopyCat功能保存配置。4.要启动闪存更新，请单击闪存更新…按钮。然后从可用更新列表中选择“v1.008.01应用程序”，然后单击下一步。按照其余屏幕提示操作，直到闪存更新过程完成并显示新固件版本（v1.008）。使用DriveExecutive进行闪存更新1.安装了闪存套件（请参阅安装闪存套件）后，启动DriveExecutive并使用连接到适配器的驱动器联机（通过以太网连接或1203-USB或22-SCM-232转换器）。2.在DriveExecutive树视图中，单击22-COMM-E适配器。然后单击信息图标，如图2所示，以显示适配器的Properties屏幕
Update Adapter
Note: There is a risk of permanent equipment damage. After starting the flash update, do not disconnect the power supply of the drive (or 22-XCOMM-DC-BASE external communication kit, if used) until the download is complete and the adapter MOD status indicator starts flashing green. If power is lost before this, the adapter may be permanently damaged. An adapter that is damaged in this way cannot be repaired. 22-COMM-E EtherNet/IP adapter firmware v1.008 5 Install flash kit 1. Please visit Allen Bradley Adapter to install the flash kit. (This will also automatically install ControlFLASH software on your computer.) 2. You can now use DriveExplorer, DriveExecutive, ControlFLASH or HyperTerminal to update the adapter. Refer to the appropriate sections below and follow the instructions. Use DriveExplorer Live/Full to Flash Update 1. After installing the Flash Kit (see Installing the Flash Kit), start DriveExplorer and go online using the drive connected to the adapter (via Ethernet connection or a 1203-USB or 22-SCM-232 converter). 2. In the DriveExplorer tree view, click 22-COMM-E EtherNet/IP.
To display the Properties screen for the adapter
On the 22-COMM-E Properties screen, click the Details tab. Important: This update may cause the adapter parameters to return to their default values. Before upgrading, you may need to save the configuration using DriveExplorer or the HIM CopyCat feature. 4. To start the flash update, click the Flash Update... button. Then select v1.008.01 Application from the list of available updates, and click Next. Follow the remaining screen prompts until the flash update process is complete and the new firmware version (v1.008) is displayed. Use DriveExecutive for flash update 1. After installing the flash kit (see Installing the flash kit), start DriveExecutive and go online using the drive connected to the adapter (via Ethernet connection or 1203-USB or 22-SCM-232 converter). 2. In the DriveExecutive tree view, click 22-COMM-E adapter. Then click the information icon, as shown in Figure 2, to display the Properties screen of the adapter
