MVME5500工控模块机器人备件
继续下一步前，再次检查电压。
隔离板更换图1 RGU隔离板表A：负载电阻器套件电流电压系列代码位于主控制板附近的典型RGU铭牌例如，此铭牌显示电流代码L和电压代码C。合适的套件为2364-SDP06A。由于铭牌显示这是一个a系列装置，TB2中不需要电阻器。a系列B出版物2364F-5.13 1999年6月RGU™ 隔离板更换5安装隔离板1.将负载电阻器固定在新板上的端子中（验证透明绝缘层没有进入端子）。拧紧至6 lb in（0.7 N-m）。注：TB2仅用于B系列RGU（见数据铭牌）。2.将电路板放在六个支架上并固定电路板。3.将端子块TB5和TB6连接至隔离板。接线板必须牢固地压入适当的插座中。4.将反馈连接连接到J1，将带状电缆连接到J2，将电流传感器连接到J7，将PE地线连接到P1。5.将Lexan防护罩更换到隔离板上。6.验证SW1设置正确（115V AC）。结束步骤安装隔离板后，更换所有Lexan屏蔽并固定隔间门。
将电路板送至自动化公司进行维修，或根据贵公司的程序和当地条例处理旧电路板！注意：SW1必须设置为适当的控制功率。将SW1设置为错误设置将导致隔离板和其他部件损坏。PN 192666取代出版物年3月版权所有1999年国际公司。在美国印刷的Lexan是通用电气公司的商标出版物2364F-5.13 1999年6月更换套件说明RGU™ 隔离板更换内容本文档介绍了如何拆卸和更换再生直流母线电源装置（RGU）中的隔离板和负载电阻器。此工具包包含的内容使用下表，验证您已收到工具包中的相应项目。
Check the voltage again before proceeding to the next step.
Isolation board replacement Figure 1 RGU isolation board Table A: Load resistor kit Current voltage series code Typical RGU nameplate located near the main control board For example, this nameplate shows current code L and voltage code C. The appropriate kit is 2364-SDP06A. Since the nameplate shows that this is a series a device, no resistor is required in TB2. A Series B Publication 2364F-5.13 June 1999 RGU ™ Replace the isolation board 5 Install the isolation board 1. Fix the load resistor in the terminal on the new board (verify that the transparent insulating layer does not enter the terminal). Tighten to 6 lb in (0.7 N-m). Note: TB2 is only used for B series RGUs (see data nameplate). 2. Place the circuit board on the six brackets and fix the circuit board. 3. Connect terminal blocks TB5 and TB6 to the isolation board. The terminal block must be firmly pressed into the appropriate socket. 4. Connect the feedback connection to J1, the ribbon cable to J2, the current sensor to J7, and the PE ground wire to P1. 5. Replace the Lexan shield onto the isolation plate. 6. Verify that SW1 is set correctly (115V AC). At the end of the step, replace all Lexan shields and secure the compartment door after installing the isolation panel.
Send the circuit board to the automation company for maintenance, or dispose of the old circuit board according to your company's procedures and local regulations! Note: SW1 must be set to the appropriate control power. Setting SW1 to the wrong setting will cause damage to the isolation panel and other components. PN 192666 replaces the publication March 1999 Copyright International Corporation. Lexan, printed in the United States, is a trademark publication of General Electric Company 2364F-5.13 Replacement Kit Description RGU, June 1999 ™ Isolation board replacement content This document describes how to remove and replace the isolation board and load resistor in the regenerative DC bus power supply unit (RGU). Use the following table to verify that you have received the corresponding items in the toolkit.
