PPE091A101 3BHE044481R0101 工控模块备件
闭合电源触点
触点托架向上移动到位并闭合电源触点。可移动接触弹簧用于提供适当的接触座。盖和底座组件中提供了减震垫，以减少捡拾和掉落的冲击！注意：国家电气规范（NEC）和地方规范概述了安全安装电气设备的规定。安装必须符合有关电线类型、导线尺寸、分支电路保护和断开装置的规范。否则可能导致人身伤害和/或设备损坏！注意：直流接触器应用或安装不当可能导致部件损坏或产品寿命缩短。布线或应用错误，如导线尺寸不当或环境温度过高，可能导致这些设备故障！
锁定主电源断路器
注意：打开并锁定主电源断路器和所有其他电源断路器，以避免意外启动受控设备造成电击或伤害的危险。出版物1370-IN011B-EN-P 2 1370直流回路接触器和接线片套件目录号说明安装安装接触器必须垂直安装在干净、干燥的位置。必须防止油、冷却剂和其他碎屑沉积在接触器上。为应用选择合适的NEMA外壳类型非常重要。还应特别考虑导线弯曲半径和导线间隙。有关凸耳套件信息。有关具体安装指南，请参阅国家电气规范和地方规范。位置1 234 1370–D C 56 a bc D a产品代码类型1370直流组件b类型代码描述D不可逆w/DB C设备代码描述C直流回路接触器D额定电流代码Amps 56 56 110 180 280位置1 23 1370–LG 40 a bc a产品代码型号1370直流元件b设备代码描述LG接线片套件C接线片额定电流代码最大值。
Close power contact
The contact carrier moves up into position and closes the power contact. The movable contact spring is used to provide a suitable contact seat. Shock pads are provided in the cover and base assembly to reduce pickup and drop impacts! NOTE: The National Electrical Code (NEC) and local codes outline provisions for the safe installation of electrical equipment. The installation must comply with the specifications for wire type, wire size, branch circuit protection and disconnecting devices. Failure to do so may result in personal injury and/or equipment damage! Note: Improper application or installation of DC contactor may cause component damage or shorten product life. Wiring or application errors, such as improper wire size or excessive ambient temperature, may cause these devices to malfunction!
Locking the main power circuit breaker
Note: Open and lock the main power circuit breaker and all other power circuit breakers to avoid the risk of electric shock or injury caused by accidental startup of controlled equipment. Publication 1370-IN011B-EN-P 2 1370 DC Circuit Contactor and Lug Kit Catalog Number indicates that the contactor must be installed vertically in a clean, dry location. Oil, coolant and other debris must be prevented from depositing on the contactors. It is important to select the appropriate NEMA enclosure type for your application. Special consideration shall also be given to conductor bending radius and conductor clearance. Information on lug kit. Refer to the National Electrical Code and local codes for specific installation guidelines. Position 1 234 1370 – D C 56 a bc D a product code type 1370 DC component b type code description D irreversible w/DB C equipment code description C DC circuit contactor D rated current code Amps 56 56 110 180 280 Position 1 23 1370 – LG 40 a bc a product code model 1370 DC component b equipment code description LG lug kit C lug rated current code maximum value.
