DS215SLCCG1AZZ01B工控机器人备件
进行安装
按照这些说明进行安装时，模块安装紧凑型I/O适用于工业环境。具体而言，本设备适用于清洁、干燥的环境（污染等级2（1））和不超过过电压II（2）类（IEC 60664-1）的电路。（3） 防止静电放电去除电源（1）污染等级2是一种通常只发生非导电污染的环境，但偶尔会出现冷凝引起的临时导电性。（2） II类过电压是配电系统的负载水平部分。在这个水平上，瞬态电压受到控制，不会超过产品绝缘的冲击电压能力。（3） 污染等级2和过电压等级II是国际电工委员会（IEC）的名称。注意！如果接触总线连接器引脚，静电放电可能会损坏集成电路或半导体。处理模块时，请遵循以下指导原则：触摸接地物体以释放静电。佩戴经批准的腕带接地装置。请勿触摸总线连接器或连接器引脚。请勿触摸模块内部的电路部件。如果可用，使用静态安全工作站。不使用时，将模块保持在其静态屏蔽盒中。注意！卸下或插入此模块之前，请先断开电源。
卸下或插入模块时
在通电的情况下卸下或插入模块时，可能会发生电弧。电弧可通过以下方式造成人身伤害或财产损失：向系统的现场设备发送错误信号，导致机器意外移动在危险环境中引发爆炸电弧会导致模块及其配套连接器上的触点过度磨损。触点磨损可能会产生电阻。紧凑型32点固态24V直流电源输出模块5出版物1769-IN031A-EN-P-2003年4月系统组件模块可在安装之前或之后连接到控制器或相邻的I/O模块。有关安装说明，请参阅第6页的面板安装，或第8页的DIN导轨安装。要使用已安装的系统，请参见第8页更换系统中的单个模块。以下步骤向您介绍如何组装紧凑型I/O系统。1.断开电源。2.检查待安装模块的母线杆是否处于解锁（完全右侧）位置。3.使用上下舌槽槽（1）将模块固定在一起（或固定在控制器上）。4.沿舌槽槽向后移动模块，直到总线连接器（2）彼此对齐。5.将母线杆轻轻向后推，以清除定位凸耳（3）。用手指或小螺丝刀。6.为了允许控制器和模块之间的通信，将总线杆完全向左移动（4），直到发出咔嗒声。确保其牢固锁定到位。注意！连接I/O模
Install
When installed according to these instructions, the module installation compact I/O is suitable for industrial environments. Specifically, this equipment is applicable to clean and dry environment (pollution level 2 (1)) and circuits not exceeding overvoltage class II (2) (IEC 60664-1). (3) Electrostatic discharge prevention and removal power supply (1) Pollution level 2 is an environment where only non-conductive pollution usually occurs, but temporary conductivity caused by condensation occasionally occurs. (2) Type II overvoltage is the load level part of the distribution system. At this level, the transient voltage is controlled and will not exceed the impulse voltage capability of the product insulation. (3) Pollution class 2 and overvoltage class II are the names of the International Electrotechnical Commission (IEC). be careful! If you touch the bus connector pins, electrostatic discharge may damage the integrated circuit or semiconductor. When handling the module, follow these guidelines: Touch a grounded object to discharge static electricity. Wear an approved wrist strap grounding device. Do not touch the bus connector or connector pins. Do not touch the circuit components inside the module. If available, use a static security workstation. When not in use, keep the module in its static shielding box. be careful! Disconnect the power supply before removing or inserting this module.
When removing or inserting a module
When removing or inserting a module with power on, arcing may occur. The electric arc can cause personal injury or property damage in the following ways: sending wrong signals to the field equipment of the system, causing accidental movement of the machine, causing explosive arc in a dangerous environment, and causing excessive wear of the contacts on the module and its mating connectors. Worn contacts can create resistance. Compact 32 point solid state 24V DC power output module 5 Publication 1769-IN031A-EN-P-April 2003 System component modules can be connected to the controller or adjacent I/O modules before or after installation. For installation instructions, refer to Panel Mounting on page 6 or DIN Rail Mounting on page 8. To use an installed system, see Replacing Individual Modules in the System on page 8. The following steps show you how to assemble a compact I/O system. 1. Disconnect the power supply. 2. Check whether the bus bar of the module to be installed is in the unlocked (full right) position. 3. Use the upper and lower tongue slots (1) to fix the modules together (or on the controller). 4. Move the module backward along the tongue slot until the bus connectors (2) are aligned with each other. 5. Push the bus bar back slightly to clear the locating lug (3). Use your fingers or a small screwdriver. 6. To allow communication between the controller and the module, move the bus bar completely to the left (4) until a click occurs. Make sure it is securely locked in place. be careful! Connecting I/O modules
