DS200TCEBG1ACD机器人模块
DeltaV M系列传统I/O
DI卡规格，8信道，120V AC，信道干触点数8隔离每个信道在250V AC检测电平下与系统进行光学隔离，开启>1.4 mA检测电平，关闭4.8V DC（>5 mA）检测电平，关断（最大。)关闭时的2 mA检测电平<0.25 mA输入阻抗5K ohm（近似值）润湿电压24V DC通道扫描速率所有16通道的0.25毫秒时间戳精度（仅适用于SOE启用通道）*0.25毫秒来自同一板卡来自同一控制器的1毫秒本地总线电流（标称12V DC）75 mA典型值，24V DC隔离时，每张卡的最大现场电路功率为100 mA，75 mA。每个通道与系统进行光学隔离，并在工厂测试为1500V DC。SOE卡的简化电路和连接图，16通道，24V DC，干触点*有关系统功能和事件序列数据收集的更多信息，请参阅事件序列产品数据表。
离散输出I/O卡DO卡规格
8通道，24V DC，隔离通道数8隔离每个通道与系统和彼此光学隔离，并在工厂测试为1500V DC。输出范围2V DC至60V DC输出额定值1.0 A关闭状态泄漏每卡最大本地总线电流（标称12V DC）1.2 mA典型值100 mA，每卡最大现场电路功率150 mA无可配置通道类型输出离散输出输出保持在控制器提交的最后状态。瞬时输出输出在预先配置的时间段（100 ms至100 s）内有效。连续脉冲输出输出在预配置的基本时间段（100 ms至100 s）中处于活动状态。分辨率=5 ms DO卡的简化电路和连接图，8通道，24V DC，隔离。DeltaV M系列传统I/O DO卡规格，8通道，24V DC，高侧通道数8隔离每个通道与系统光学隔离，并在工厂测试为1500V DC。
DeltaV M-Series Traditional I/O
DI card specification, 8-channel, 120V AC, 8 channel dry contact points, each channel is optically isolated from the system at 250V AC detection level, turn on>1.4 mA detection level, turn off 4.8V DC (>5 mA) detection level, and turn off (maximum) 2 mA detection level when off<0.25 mA input impedance 5K ohm (approximate value) Wetting voltage 24V DC channel scanning rate 0.25 ms timestamp accuracy of all 16 channels (only applicable to SOE enabled channels) * 0.25 ms local bus current (nominal 12V DC) 75 mA typical value from the same controller of the same board. When 24V DC is isolated, the maximum field circuit power of each card is 100 mA, 75 mA. Each channel is optically isolated from the system and tested at the factory to be 1500V DC. Simplified circuit and connection diagram of SOE card, 16 channels, 24V DC, dry contact * For more information about system functions and event sequence data collection, please refer to the event sequence product data sheet.
Discrete Output I/O Card DO Card Specifications
8 channels, 24V DC, the number of isolation channels is 8, each channel is optically isolated from the system and each other, and tested to be 1500V DC in the factory. Output range 2V DC to 60V DC Output rating 1.0 A Closed state Leakage Maximum local bus current per card (nominal 12V DC) 1.2 mA Typical value 100 mA, Maximum field circuit power per card 150 mA No configurable channel type output Discrete output remains in the last state submitted by the controller. The instantaneous output is valid for a pre configured time period (100 ms to 100 s). The continuous pulse output is active for a pre configured basic time period (100 ms to 100 s). Simplified circuit and connection diagram of DO card with resolution=5 ms, 8-channel, 24V DC, isolated. DeltaV M series traditional I/O DO card specification, 8-channel, 24V DC, number of high side channels 8, each channel is optically isolated from the system, and tested to be 1500V DC in the factory.
