DS200QTBAG1ADC工控机器人备件
设备管理器
HART通信支持AMS设备管理器的HART传递。控制功能的HART变量和状态报告。每个启用通道的Hart扫描时间600–800 mS（典型值）DeltaV M系列传统I/O 2022年10月www.emerson。com/deltav 7 RTD输入卡规格，每卡8通道RTD通道8个传感器类型2线、3线或4线传感器配置电阻，Pt100、Pt200、Pt500、Ni120、Cu10，用户定义满量程信号范围见下表精度见下表重复性0.05%量程A/D分辨率16位校准无需单位°C，°F传感器励磁电流100µA共模抑制120 dB，50/60 Hz共模阻抗>10兆欧本地总线电流（标称12V DC）
安装类别
4通道通道数4隔离CAN/CSA-C22.2 No.100.1-92安装类别II，污染等级2通道至系统-600V AC双绝缘。每个通道与系统进行光学隔离，并在工厂进行5000V DC测试。通道至通道-600V基本绝缘。每个通道彼此光学隔离，并在工厂测试为3100V DC。介电强度信道到系统-3700V RMS信道到信道-2200V RMS ADC分辨率16位-3dB滤波器频率2.7 Hz DC/50/60 Hz共模抑制120 dB输入阻抗10兆欧热电偶传感器类型B、E、J、K、N、R、S、T，未描述的RTD传感器类型PT100、PT200、Ni120、Cu10，电阻/用户定义的mV和V范围参考下表输入类型混合可独立配置的环境温度-40°至70°C校准无需安装I/O载体的指定插槽LocalBus额定功率12V DC，350 mA，无需现场电源隔离输入卡
Device Manager
HART communication supports HART transfer of AMS Device Manager. HART variables and status reports for control functions. Hart scan time per enabled channel 600 – 800 mS (typ.) DeltaV M Series Traditional I/O October 2022 www emerson。 Com/deltav 7 RTD input card specifications, each card has 8 channels, 8 RTD channels, 8 sensor types, 2-wire, 3-wire or 4-wire sensors with resistance, Pt100, Pt200, Pt500, Ni120, Cu10, and the user defined full range signal range is shown in the following table. The accuracy is shown in the following table. The repeatability is 0.05%. The range A/D resolution 16 bit calibration does not require unit ° C, the ° F sensor excitation current 100 µ A common mode suppression 120 dB, 50/60 Hz common mode impedance>10 megohm local bus current (nominal 12V DC)
Installation category
Number of 4 channels: 4 isolation CAN/CSA-C22.2 No.100.1-92, installation category II, pollution level: 2 channels to system - 600V AC double insulation. Each channel is optically isolated from the system and tested at 5000 V DC in the factory. Channel to channel - 600V basic insulation. Each channel is optically isolated from each other and tested at the factory to be 3100V DC. Dielectric strength channel to system-3700V RMS channel to channel-2200V RMS ADC resolution 16 bit - 3dB filter frequency 2.7 Hz DC/50/60 Hz common mode rejection 120 dB input impedance 10 megohm thermocouple sensor types B, E, J, K, N, R, S, T, unspecified RTD sensor types PT100, PT200, Ni120, Cu10, For resistance/user-defined mV and V range, refer to the following table. Input types can be mixed and independently configured. Ambient temperature is - 40 ° to 70 ° C. Calibration does not need to install I/O carriers. The specified slot LocalBus has a rated power of 12V DC, 350 mA. No field power isolation input card is required
