DS200TCDAG1BDB数控系统模块
准备好编程
CPU现在已准备好编程（如果并行连接，则无论键位置如何，都可以对CPU进行编程）。程序验证后，拨动开关可以移动到适当的操作模式位置；启用输出运行、禁用输出运行或停止。七个LED指示拨动开关的位置、内存保护状态、串行端口活动状态和程序状态。编程器连接，并行对于并行接口（仅限MS-DOS编程器），编程器与总线变送器模块（IC697BEM713）的顶部端口相连，如图1所示。有关编程功能的说明，请参阅适用的编程软件用户手册。内存保护a45723开路更换电池连接器1 MBYTE内存板CPX 782当前安装的电池连接器内存保护钥匙开关Y R E B A T模块IC697CPX782标签44A726758–152R01串行端口3在插槽1中使用此模块，顶部远程编程器上仅CPX 782OFF正常运行EN ON=正常，启用，保护前运行，输出启用运行，输出禁用停止键位置模块功能电池连接器在拔下旧电池之前安装新电池。
存储器保护
使用IC697ACC701存储器保护RS-485兼容的96 MHz 32位中央处理单元P1 P2 P3串行端口2 RS-485兼容性工厂测试串行端口1 RS-232状态LED运行/停止开关串行端口2 RS-485串行端口1 RS-232工厂测试仅串行端口3 RS-485图2 CPX 782-主要功能96 MHz、32位、浮点、，1 Mbyte内存中央处理单元GFK-1431F 4 PLC CPU 1999年11月系列90-70可编程控制器数据表手册GFK-0600F 20-4 B R M a45301 IC66*块编程器机架1机架0 P S C U B T M G B C R M IC66*总线（最大7500英尺）机架7从底部到最后一个BRM的所有互连电缆的总长度为最大50英尺。
Ready to program
The CPU is now ready for programming (if connected in parallel, the CPU can be programmed regardless of the key position). After program verification, the toggle switch can be moved to the appropriate operating mode position; Enable output run, disable output run, or stop. The seven LEDs indicate the position of the toggle switch, memory protection status, serial port activity status, and program status. The programmer is connected in parallel. For the parallel interface (MS-DOS programmer only), the programmer is connected to the top port of the bus transmitter module (IC697BEM713), as shown in Figure 1. For a description of the programming functions, refer to the applicable programming software user manual. Memory protection a45723 Open circuit Replace battery connector 1 MBYTE memory board CPX 782 Currently installed battery connector Memory protection key switch Y R E B A T module IC697CPX782 label 44A726758 – 152R01 Serial port 3 uses this module in slot 1. Only CPX 782 on the top remote programmer runs normally EN ON=normal, enable, run before protection, output enable, run, The output disable stop key position module function battery connector installs a new battery before removing the old battery.
Memory protection
Use IC697ACC701 memory to protect RS-485 compatible 96 MHz 32-bit central processing unit P1 P2 P3 serial port 2 RS-485 compatibility Factory test Serial port 1 RS-232 status LED run/stop switch Serial port 2 RS-485 serial port 1 RS-232 Factory test Serial port 3 RS-485 Figure 2 CPX 782 - Main functions 96 MHz, 32-bit, floating point, 1 Mbyte memory central processing unit GFK-1431F 4 PLC CPU November 1999 Series 90-70 Programmable Controller Data Sheet Manual GFK-0600F 20-4 B R M a45301 IC66 * block programmer rack 1 rack 0 P S C U B T M G C R M IC66 * bus (maximum 7500 feet) rack 7 The total length of all interconnecting cables from the bottom to the last BRM is a maximum of 50 feet.
