DS200TCQCG1BEF机器人模块卡件
保护和认证
同一IOM上的其他频道将不受影响。AI、AO和DI通道经过进一步保护和认证，可支持能量受限/非易燃现场接线连接至2区/2区危险位置。Experion Series-C输入/输出规范，EP03-490-520 45版本1.5霍尼韦尔专有2021 12月详细规范-模拟输入参数规范输入类型电流（2、3或4线设备）输入通道每个模块最大32个（带或不带开路检测）A/D转换器分辨率16位输入范围0-20 mA或4-20 mA正常模式抑制比50 Hz时18 dB，60 Hz输入滤波器响应时为20 dB，单极，6 Hz串扰时为-3 dB，dc至60 Hz（通道至通道）60 dB输入阻抗250Ω输入电压范围（任何参考公共输入，无损坏）+33 VDC至-1 VDC（1）输入扫描速率10 ms硬件精度满标度0.1%（23.5±2°C）满标度0.175%（0至+70°C）0.25%（-40至+70℃）短路电流限制25 mA注1：返回端子直接连接至公共（接地）详细信息规格–脉
冲输入参数规格信
道任何4信道频率0-15 kHz最小脉冲宽度25µs占空比任何满足最小脉冲宽度规格Experion Series-C I/O规格的占空比，EP03-490-520 46版本1.5霍尼韦尔专有2021 12月详细规范-带HART1参数规范的模拟输出输出输出输出类型4-20 mA输出通道32最大每个模块2输出温度漂移0.007%满标度/°C输出回读诊断±4%满标量输出电流线性±0.05%满标程（标称）分辨率12位校准精度<0.35%满量程（25oC），包括线性可直接设置输出电流范围0 mA、2.9 mA至21.1 mA最大电阻负载（24 V电源）825欧姆@20 mA最大输出兼容电压（24 V供电）16.5 VDC@20 mA开路电压电源电压（26 VDC最大）响应时间，DAC输入代码在HART模式下输出（在最终值的3%以内）80 ms，在非HART模式中0.25 ms，在切换0 ms时输出到现场的间隙（0 mA）（两个合作伙伴持续激活）注1：如果AO通道的配置从非HART改为HART，且模拟OP保持通电，则通道重新加载时，输出的干扰不超过65 ms。将AO通道从HART更改为非HART不会产生任何OP干扰。注2：请参考《用户指南》，了解确定信道使用与工作温度的计算方法。
Protection and certification
Other channels on the same IOM will not be affected. AI, AO and DI channels are further protected and certified to support energy limited/non incendive field wiring to Zone 2/Zone 2 hazardous locations. Experion Series-C input/output specification, EP03-490-520 45 version 1.5 Honeywell proprietary December 2021 detailed specification - Analog input parameter specification Input type Current (2, 3 or 4-wire device) Input channel maximum 32 per module (with or without open circuit detection) A/D converter resolution 16 bit input range 0-20 mA or 4-20 mA Normal mode rejection ratio 18 dB at 50 Hz, 20 dB at 60 Hz input filter response, - 3 dB at 6 Hz crosstalk, Dc to 60 Hz (channel to channel) 60 dB input impedance 250 Ω input voltage range (any reference to common input, no damage)+33 VDC to - 1 VDC (1) input scanning rate 10 ms Hardware accuracy Full scale 0.1% (23.5 ± 2 ° C) Full scale 0.175% (0 to+70 ° C) 0.25% (- 40 to+70 ° C) Short circuit current limit 25 mA Note 1: Return terminals are directly connected to common (ground) Details Specification – Pulse
Input parameter specification information
Channel Any 4-channel frequency 0-15 kHz Minimum pulse width 25 µ s duty cycle Any duty cycle that meets the minimum pulse width specification Experion Series-C I/O specification, EP03-490-520 46 version 1.5 Honeywell proprietary December 2021 detailed specification - Analog output with HART1 parameter specification Output type 4-20 mA Output channel 32 Maximum output temperature drift of each module 2 0.007% Full scale/° C output back reading diagnosis ± 4% Full scale output current linear ± 0.05% Full scale (nominal) resolution 12 bit calibration accuracy<0.35% Full scale (25oC), including linear output current range 0 mA 2.9 mA to 21.1 mA maximum resistive load (24 V power supply) 825 ohms @ 20 mA maximum output compatible voltage (24 V power supply) 16.5 VDC@20 The response time of the mA open circuit voltage power supply voltage (26 VDC maximum), the DAC input code output (within 3% of the final value) 80 ms in HART mode, 0.25 ms in non HART mode, and the output gap to the site (0 mA) when switching 0 ms (two partners continuously activate) Note 1: If the configuration of the AO channel is changed from non HART to HART, and the analog OP remains powered on, the output interference will not exceed 65 ms when the channel is reloaded. Changing the AO channel from HART to non HART will not cause any OP interference. Note 2: Please refer to the User's Guide for the calculation method to determine the channel use and operating temperature.
