DS200SDCCG4AEC工控备件
详细规范-总线24VDC
DO参数规范输入/输出型号CC-PDOB01-24V数字输出，现场隔离，总线输出IOTA型号CC-TDOB01非冗余9“CC-TDOB11冗余12”输出通道32输出类型电源负载电压15 30 VDC最大负载电流1.5A 6A电流隔离1500 VAC RMS或±1500 VDC Experion Series-C输入/输出规范，EP03-490-520 35版本1.5霍尼韦尔专有2021 12月24 V（典型）状态电压参数规范，负载电流@0.5A关闭状态电压0v VDC（最大值）（空载条件下指示的最大值为3.3VDC）关闭状态泄漏电流5.0µA（最大）开启/关闭时间10 ms（最大）无切换（0ms）（仅适用于冗余）时输出到场的间隙（0电流）输出电压将为电源电压–150mV最大值。注1：一个/两个短路条件参数表示在短路保护机制禁用功能之前指示短路条件时，可以通过DO的最大电流。
输入/输出规范
Experion Series-C输入/输出规范，EP03-490-520 36版本1.5霍尼韦尔专有2021 12月5.17日。数字输出-继电器IOTA-使用CC-PDOB01 IOM功能数字输出继电器为隔离的低压/低电流或高压/高电流离散输出应用提供干触点。每个继电器支持基于跳线配置的Form-a或Form-B输出。继电器IOTA使用带有特殊IOTA的数字输出24V（DO24V）IOM来支持继电器IOTA。DO24V IOM的所有特性都包含在这里。值得注意的特点•电流隔离•插座式继电器•隔离干触点•常开触点和常闭触点之间的跳线选择•反电动势缓冲电路•每个通道开启状态的LED指示详细规范-继电器DO IOTA参数规范输入/输出型号CC-PDOB01-24V现场隔离
Detail Specification - Bus 24VDC
DO parameter specification Input/output model CC-PDOB01-24V digital output, field isolation, bus output IOTA model CC-TDOB01 non redundant 9 "CC-TDOB11 redundant 12" output channel 32 output type power load voltage 15 30 VDC maximum load current 1.5A 6A current isolation 1500 VAC RMS or ± 1500 VDC Experience Series-C input/output specification, EP03-490-520 35 version 1.5 Honeywell proprietary 2021 December 24 V (typical) state voltage parameter specification, Load current @ 0.5A Closing state voltage 0v VDC (maximum value) (the maximum value indicated under no-load conditions is 3.3VDC) Closing state leakage current 5.0 µ A (maximum) Opening/closing time 10 ms (maximum) No switching (0ms) (only applicable to redundancy) When the gap (0 current) output voltage to the field will be the power supply voltage – 150mV maximum. Note 1: One/two short-circuit condition parameters indicate the maximum current that can pass through DO when the short-circuit condition is indicated before the short-circuit protection mechanism is disabled.
Input/output specifications
Experion Series-C input/output specification, EP03-490-520 36 version 1.5, Honeywell proprietary, December 5.17, 2021. Digital Output - Relay IOTA - The digital output relay uses the CC-PDOB01 IOM function to provide dry contacts for isolated low-voltage/low current or high-voltage/high current discrete output applications. Each relay supports Form-a or Form-B outputs based on jumper configuration. Relay IOTA uses digital output 24V (DO24V) IOM with special IOTA to support relay IOTA. All features of DO24V IOM are included here. Notable features • Current isolation • Receptacle relay • Isolated dry contact • Jumper selection between normally open contact and normally closed contact • Back EMF buffer circuit • Detailed specification for LED indication of open status of each channel - Relay DO IOTA parameter specification Input/output model CC-PDOB01-24V Field isolation
