DS200TCQCG1BJF工控模块备件
在电源线频率下
在250 负载输出温度漂移0.005%满量程/°C输出回读精度±4%满量程输出电流线性度±0.05%满量程标称分辨率±0.05%全量程校准精度±0.35%满量程（25oC），包括线性度直接设定输出电流范围0 mA，2.9 mA至21.1 mA最大电阻负载（24 V电源=22 VDC至28 VDC）800欧姆Experion C系列I/O规格，EP03-490-520 22版本1.5霍尼韦尔专有2021 12月参数规范最大输出兼容电压（24 V电源=22 VDC到28 VDC）16 V最大开路电压22 V响应时间（DAC输入代码到输出）在最大10 ms切换时输出到现场的80 ms间隙（0 mA）内沉降到最终值的1%以内（仅适用于冗余）Experion Series-C I/O规范，EP03-490-520 23版本1.5霍尼韦尔专有2021 12月9。
模拟输出
具有HART–CC-PAOH51功能模拟输出（AO）模块向执行器和记录/指示设备提供高电平恒定电流。值得注意的功能•广泛的自诊断•可选冗余•HART可用于状态和配置•安全状态（FAILOPT）行为可按通道配置•非易燃输出FAILOPC系列AO模块支持按通道的FAILOPD参数。用户可以将每个通道配置为保持最后一个值或设置为安全值。如果IOM设备电子设备发生故障，输出将始终归零，即安全状态。
At power line frequency
The output temperature drift of 250 Ω· load is 0.005% of the full range/° C, the output readback accuracy is ± 4% of the full range output current, the linearity is ± 0.05% of the full range nominal resolution is ± 0.05% of the full range calibration accuracy is ± 0.35% of the full range (25oC), including the linearity, the direct setting output current range is 0 mA, 2.9 mA to 21.1 mA, the maximum resistance load (24 V power supply=22 VDC to 28 VDC), 800 ohm Experion C series I/O specifications, EP03-490-520 22 version 1.5 Honeywell proprietary 2021 December parameter specification Maximum output compatible voltage (24 V power supply=22 VDC to 28 VDC) 16 V maximum open circuit voltage 22 V response time (DAC input code to output) The 80 ms gap (0 mA) output to the site during maximum 10 ms switching subsides to within 1% of the final value (only applicable to redundancy) Experience Series-C I/O specification, EP03-490-520 23 version 1.5 Honeywell proprietary 2021 December 9.
Analog Output
The analog output (AO) module with HART – CC-PAOH51 function provides high level constant current to the actuator and recording/indicating equipment. Notable functions • Extensive self diagnosis • Optional redundancy • HART can be used for status and configuration • Safe state (FAILOPT) behavior can be configured by channel • Non incendive output FAILOPC series AO modules support FAILOPD parameters by channel. You can configure each channel to hold the last value or set it as a safe value. If the electronic device of the IOM device fails, the output will always return to zero, that is, the safe state.
