MVME-147A工控备件
参数规范注释1:
CC-PAIH01支持信道13-16的电压输入。当与CC-TAIDx1 IOTA一起使用时，CC-PAIH102支持信道1-16的电压输入。每个通道的250欧姆负载电阻器通过IOTA上的跳线连接到输入端子。用户应在与电压变送器一起使用的通道上切断该跳线。对于通道13-16，低压侧输入连接通常通过IOTA上的跳线连接到系统公共端。该跳线可由用户切断，以便在CMV规格范围内进行差动操作。Experion Series-C输入/输出规范，EP03-490-520 13版本1.5霍尼韦尔专有2021 12月5.4。模拟输入–CC-PAIN01功能模拟输入模块接受传感设备的高电平电流输入。值得注意的功能•广泛的自我诊断•可选冗余•提供非易燃现场电源•快速环路扫描非易燃电源提供非易燃电源，无需外部编组，即可支持4-20mA环路，并仍提供通道电源保护。
非易燃额定功率
该保护支持2类危险保护非易燃额定功率。详细规范-模拟输入参数规范输入/输出型号CC-PAIN01-高电平模拟输入IOTA型号CC-TAIN01非冗余6“CC-TAIN1冗余12”输入型电流（2线或自供电变送器）输入通道16通道（16单端）共模抑制比，直流至60 Hz（500 电源不平衡）70 dB A/D转换器分辨率16位输入范围4-20 mA（至200Ω）正常模式抑制比，60 Hz时20 dB正常模式滤波器响应单极RC，-3 dB@6.0 Hz最大正常模式输入±30 V串扰，dc至60 Hz（通道至通道）-60 dB输入扫描速率50 ms硬件精度（@CMV=0 V）±满标度的0.075%（23.5°±2°C）±满刻度的0.15%（0至60°C）变送器现场功率调节1类2类非易燃接口的单独保护限流电路。无需熔断Experion Series-C输入/输出规范，EP03-490-520 14版本1.5霍尼韦尔专有2021 12月5.5。低电平模拟（温度）输入–LLMUX–CC-PAIM01功能LLMUX IOP模块支持多达64个通道的温度输入。
Parameter specification note 1:
CC-PAIH01 supports voltage input of channels 13-16. When used with CC-TAIDx1 IOTA, CC-PAIH102 supports the voltage input of channels 1-16. The 250 ohm load resistor for each channel is connected to the input terminals via jumpers on the IOTA. The user should disconnect this jumper on the channel used with the voltage transmitter. For channels 13-16, the low-voltage side input connection is usually connected to the system common through the jumper on the IOTA. This jumper can be cut by the user for differential operation within the CMV specification. Experion Series-C input/output specification, EP03-490-520 13 version 1.5 Honeywell proprietary December 5.4, 2021. Analog Input – The CC-PAIN01 function analog input module accepts high-level current input from the sensing device. Notable functions • Extensive self diagnosis • Optional redundancy • Providing non flammable on-site power supply • Fast loop scanning non flammable power supply provides non flammable power supply, which can support 4-20mA loop without external marshalling, and still provide channel power protection.
Non incendive rating
This protection supports a Class 2 hazard protection non incendive rating. Detailed specification - Specification of analog input parameters Input/output model CC-PAIN01 - high-level analog input IOTA model CC-TAIN01 non redundant 6 "CC-TAIN1 redundant 12" input current (2-wire or self powered transmitter) Input channel 16 channels (16 single ends) common mode rejection ratio, DC to 60 Hz (500 ｜ power imbalance) 70 dB A/D converter resolution 16 bit input range 4-20 mA (to 200 Ω) normal mode rejection ratio, 20 dB normal mode filter response unipolar RC at 60 Hz, - 3 dB@6.0 Hz maximum normal mode input ± 30 V crosstalk, dc to 60 Hz (channel to channel) - 60 dB input scan rate 50 ms hardware accuracy (@ CMV=0 V) ± 0.075% of full scale (23.5 ° ± 2 ° C) ± 0.15% of full scale (0 to 60 ° C) transmitter field power regulation Class 1 Class 2 non flammable interface single protection current limiting circuit. It is unnecessary to fuse the Experion Series-C input/output specification, EP03-490-520 14 version 1.5 Honeywell proprietary December 5.5, 2021. Low level analog (temperature) input – LLMUX – CC-PAIM01 function LLMUX IOP module supports up to 64 channels of temperature input.
