FBM232 P0926GW工控机器人备件
功能模拟输入模块
接受来自变送器和传感装置的高电平电流或电压输入。显著特点•广泛的自我诊断•可选冗余•开路检测•提供非易燃现场电源•非易燃电源•支持HART，用于快速收集控制变量的多变量仪表和多个调制解调器•快速环路扫描•通过开路检测诊断进行PV保护•开路不良PV检测详细规范–模拟输入HART参数规范输入/输出型号CC-PAIH02–高电平模拟输入HARTIOTA型号非冗余冗余CC-TAIX01 CC-TAIX11CC-GAIX21 CC-GAIX11 CC-TAID01 CC-TAID11输入类型电压、电流（2线或自供电变送器）输入通道1 16通道（12单端/4差分）共模抑制比，直流至60 Hz（500 电源不平衡）70 dB共模电压，直流至60 Hz-6至+5 V峰值A/D转换器分辨率16位输入范围1 0至5 V，1至5 V、0.4至2 V、4-20 mA（通过250Ω）正常模式抑制比，在60 Hz 19 dB Experion Series-C输入/输出规范下，EP03-490-520 9版本1.5霍尼韦尔专有Dec 2021参数规范正常模式滤波器响应单极RC，-3 dB@6.5 Hz最大正常模式输入（差分输入，无损坏）±30 V串扰，dc至60 Hz（通道至通道）-60 dB输入阻抗（电压输入）>10 MΩ供电输入扫描速率50 ms硬件精度（CMV=0 V）±满标度的0.075%（23.5°±2°C）±满刻度的0.15%（0至60°C）变送器现场功率调节1类2类非易燃接口的单独保护限流电路。
无需熔断注
1:CC-PAIH01支持通道13-16的电压输入。当与CC-TAIDx1 IOTA一起使用时，CC-PAIH 02支持通道1-16的电压输入。每个通道的250欧姆负载电阻器通过IOTA上的跳线连接到输入端子。用户应在与电压变送器一起使用的通道上切断该跳线。对于通道13-16，低压侧输入连接通常通过IOTA上的跳线连接到系统公共端。该跳线可由用户切断，以便在CMV规格范围内进行差动操作。Experion Series-C输入/输出规范，EP03-490-520 10版本1.5霍尼韦尔专有2021 12月5.2。模拟输入具有HART–CC-PAIH51功能模拟输入模块接受来自变送器和传感设备的高电平电流输入。显著特点•广泛的自我诊断•可选冗余•提供非易燃现场电源（无外部用户供电）•适用于HART设备的配置/状态•支持HART，用于快速收集控制变量的多变量仪表•快速回路扫描•非易燃电源详细规范–带HART参数规范输入/输出型号CC-PAIH51的模拟输入-带HART IOTA型号CC-TAIX51的高电平模拟输入非冗余6“CC-TAIX61冗余12”输入型电流（2线或自供电变送器）输入通道1 16通道（所有单端）。共模抑制比，直流至60 Hz（500 电源不平衡）70 dB共模电压，直流至60 Hz-6至+5 V峰值A/D转换器分辨率16位输入范围1 4-20 mA（至200Ω）正常模式抑制比，在60 Hz时19 dB正常模式滤波器响应单极RC，在6.5 Hz时-3 dB最大正常模式输入±30 V串扰，dc至60 Hz（通道至通道）-60 dB输入扫描速率50 ms硬件精度（@CMV=0 V）±满标度的0.075%（23.5°±2°C）±满刻度的0.15%（0至60°C）变送器现场功率调节1类2类非易燃接口的单独保护限流电路。
Functional analog input module
Accepts high-level current or voltage inputs from transmitters and sensing devices. Notable features • Extensive self diagnosis • Optional redundancy • Open circuit detection • Non incendive on-site power supply • Non incendive power supply • HART support, Multivariable instrument and multiple modems for fast collection of control variables • Fast loop scanning • PV protection through open circuit detection diagnosis • Detailed specification for poor open circuit PV detection – Analog input HART parameter specification Input/output model CC-PAIH02 – High level analog input HART model Non redundant redundancy CC-TAIX01 CC-TAIX11CC-GAIX21 CC-GAIX11 CC-TAID01 CC-TAID11 Input type Voltage Current (2-wire or self powered transmitter) Input channel 1 16 channel (12 single ended/4 differential) common mode rejection ratio, DC to 60 Hz (500 Ω power imbalance) 70 dB common mode voltage, DC to 60 Hz - 6 to+5 V peak A/D converter resolution 16 bit input range 10 to 5 V, 1 to 5 V, 0.4 to 2 V, 4-20 mA (through 250 Ω) normal mode rejection ratio, at 60 Hz 19 dB Experience Series - C input/output specifications, EP03-490-520 9 Version 1.5 Honeywell proprietary Dec 2021 parameter specification Normal mode filter response unipolar RC, - 3 dB@6.5 Hz maximum normal mode input (differential input, no damage) ± 30 V crosstalk, dc to 60 Hz (channel to channel) - 60 dB input impedance (voltage input)>10 M Ω power supply Input scanning rate 50 ms Hardware accuracy (CMV=0 V) ± 0.075% of full scale (23.5 °± 2 ° C) ± 0.15% of full scale (0 to 60 ° C) Separate protection current limiting circuit for Class 1 and Class 2 non flammable interfaces of transmitter field power regulation.
No fuse is required
1: CC-PAIH01 supports voltage input of channels 13-16. When used with CC-TAIDx1 IOTA, CC-PAIH 02 supports the voltage input of channels 1-16. The 250 ohm load resistor for each channel is connected to the input terminals via jumpers on the IOTA. The user should disconnect this jumper on the channel used with the voltage transmitter. For channels 13-16, the low-voltage side input connection is usually connected to the system common through the jumper on the IOTA. This jumper can be cut by the user for differential operation within the CMV specification. Experion Series-C input/output specification, EP03-490-520 10 version 1.5 Honeywell proprietary December 5.2, 2021. Analog input with HART – CC-PAIH51 function Analog input module accepts high-level current input from transmitter and sensing equipment. Highlights • Extensive self diagnosis • Optional redundancy • Non incendive field power supply (no external user power supply) • Configuration/status for HART devices • HART support, Multivariable instrument for fast collection of control variables • Fast loop scanning • Detailed specification of non incendive power supply – Analog input with HART parameter specification input/output model CC-PAIH51 - High level analog input with HART IOTA model CC-TAIX51 Non redundant 6 "CC-TAIX61 redundant 12" input type current (2-wire or self powered transmitter) Input channel 1 16 channels (all single ends). Common mode rejection ratio, 70 dB common mode voltage from DC to 60 Hz (500 Ω power supply imbalance), 16 bit input range of DC to 60 Hz-6 to+5 V peak A/D converter resolution, 1 4-20 mA (to 200 Ω) normal mode rejection ratio, 19 dB normal mode filter response unipolar RC at 60 Hz, - 3 dB maximum normal mode input ± 30 V crosstalk at 6.5 Hz, Dc to 60 Hz (channel to channel) - 60 dB input scan rate 50 ms Hardware accuracy (@ CMV=0 V) ± 0.075% of full scale (23.5 ° ± 2 ° C) ± 0.15% of full scale (0 to 60 ° C) Transmitter field power regulation Class 1 Class 2 non flammable interface separate protection current limiting circuit.
