ABB DSTA131 工控备件
使用外部驱动信号运行FAST功能
这是一个用于快速转发程序操作的功能使用连续信号控制固定外部信号输入。打开（ON）后约0.5秒或更长时间后，状态变为FAST只有在模式1的“程序驱动系统”中选择“MASTER EXT”或“MASTR FREE”时，才启用该功能。▪执行条件和操作内容等类似于第9.2.6节中的“程序操作和运行操作”。PTN 1 PTN 2 PTN 4 PTN 8 PTN10 PTN 20･模式号（PTN）由外部信号输入选择。･图案编号选择基于BCD代码产生的控制信号固定外部信号输入由连续信号控制。参见下表示例，根据要选择的模式编号，使用○ 做记号导通（ON）后约0.5秒内选择模式编号。此外，除了○ 标记取决于图案编号。例如，当选择模式10时，
选择传导PTN8和PTN2
选择模式1至30以外的PTN No.9 PTN No.8 PTN No.7 PTN No.6 PTN No.5 PTN No.4 PTN No.3 PTN No.2 PTN No.BCD代码，之前选择的模式号保持原样。･只有在模式1的“模式选择系统”中选择了“EXT”或“FREE”时才启用。･例如，如果只需要选择从1到4的模式号，也只能分配PTN 1、PTN 2、PTN 4的3个外部信号输入。･执行条件和操作内容等类似于第9-2节“程序操作和运行操作”。*从工厂发货时，未显示设置条件“---------------------”。如果设置任何功能一次，则不显示未设置条件。分配设置未初始化（无设置条件），即使设置内容已初始化。
Running FAST functions with external drive signals
This is a function for fast forwarding program operation that uses continuous signals to control fixed external signal inputs. After being turned on (ON) for about 0.5 seconds or more, the status changes to FAST. This function is enabled only when "MASTER EXT" or "MASTR FREE" is selected in "Program Driver System" of mode 1. ▪ Execution conditions and operation contents are similar to "program operation and operation" in Section 9.2.6. PTN 1 PTN 2 PTN 4 PTN 8 PTN10 PTN 20 ¥ The mode number (PTN) is selected by the external signal input. ¥ Pattern number selection is based on the control signal generated by BCD code. Fixed external signal input is controlled by continuous signal. Refer to the following example. Select the mode number according to the mode number to be selected. Use ○ to mark the mode number in about 0.5 seconds after turning on (ON). In addition, except for the ○ mark, it depends on the pattern number. For example, when mode 10 is selected,
Select conductive PTN8 and PTN2
Select PTN No. 9, PTN No. 8, PTN No. 7, PTN No. 6, PTN No. 5, PTN No. 4, PTN No. 3, PTN No. 2, PTN No. BCD code other than modes 1 to 30, and the previously selected mode number remains unchanged It is only enabled when "EXT" or "FREE" is selected in the "Mode Selection System" of mode 1 For example, if only the mode numbers from 1 to 4 need to be selected, only three external signal inputs of PTN 1, PTN 2 and PTN 4 can be allocated The execution conditions and operation contents are similar to Section 9-2 "Program Operation and Operation"* When shipping from the factory, the set condition "---------------------" is not displayed. If any function is set once, the unset condition is not displayed. The allocation settings are not initialized (no setting conditions), even if the settings are initialized.
